Chamberlain WHISPER DRIVE HD900D - Manual (Page 32)

32
Using the Wall-Mounted Door Control
THE SMART CONTROL PANEL ®
Press the push button to
open or close the door.
Press again to reverse
the door during the
closing cycle or to stop the
door while it’s opening.
This door control
contains a motion
detector that will automatically turn on
the light when it detects a person entering the garage. This feature
can be easily turned off for extended work light use.
Light Feature
Press the Light button to turn the opener light on or off.
It will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the light will
remain on for 4-1/2 minutes. Press again to turn it off sooner. The
4-1/2 minute interval can be changed to 1-1/2, 2-1/2 or 3-1/2
minutes as follows: Press and hold the Lock button until the light
blinks (about 10 seconds). A single blink indicates that the timer
is reset to 1-1/2 minutes. Repeat the procedure and the light will
blink twice, resetting the timer to 2-1/2 minutes. Repeat again for
a 3-1/2 minute interval, etc., up to a maximum of four blinks and
4-1/2 minutes.
When using the opener lights as working lights, we recommend
that you first disable the motion sensor.
Lock Feature
Designed to prevent operation of the door from hand-
held remote controls. However, the door will open and
close from the Door Control, the Outside Keylock and the Keyless
Entry Accessories.
To activate, press and hold the Lock button for 2 seconds. The
Smart Control Panel
® will display the following message: “LOCK
MODE REMOTE CONTROL LOCKED OUT PRESS LOCK BUTTON
TO ENABLE REMOTE.”
To turn off, press and hold the Lock button again for 2 seconds.
The Lock feature will also turn off whenever the “learn” button is
activated.
Motion Detecting Light Feature
The opener light will turn on automatically when a person walks in
front of the wall-mounted door control. This feature works by
detecting motion and body heat and may not work in
temperatures around 100˚ F (37.7˚ C). The opener light will come
on for 5 minutes, then shut off automatically if no additional
motion or heat differential is calculated.
To disable this feature, press the Motion Detecting Light On/Off
button on the left side of the door control.
We recommend that you disable the motion sensor
when using the opener lights as working lights.
Otherwise, they will turn off automatically if you are
working beyond the sensor’s range.
(Prog) Learn Feature
The door control is equipped with a Prog <LEARN> button to
assist in learning remote controls to the unit. Press the Prog
<LEARN> button once to initiate LEARN mode and the display will
show ‘Learn Remote Control - Press Learn Button Again to
Confirm’. Press the Prog <LEARN> button a second time and the
display will show ‘Learn Mode - Press Remote Control Button to
Learn Remote.’ Press the button of the remote control to be
learned and the work light will blink to confirm the remote control
has been learned.
Hour & Minute Feature
Press or hold either of these side buttons to
increment the hour or minute displayed on the
LCD display.
(Lang) Language Feature
Press this side button to toggle between the three languages -
English, Spanish, and French.
Degrees F/C Feature
Press this side button to toggle the temperature units
between Fahrenheit and Celsius.
Additional feature when used with the 3-Button hand-held
remote
To control the opener lights:
In addition to operating the door, you may program the remote to
operate the lights.
1. With the door closed, press and hold a small
remote button that you want to control the
light.
2. Press and hold the Light button on the door control.
3. While holding the Light button, press and hold the Lock button
on the door control.
4. After the opener lights flash, release all buttons.
Motion Sensing
ON/OFF
Prog <LEARN>
Hour
Minute
Language
Degrees (F/C)
Lock Button
Light Button
Push Bar
LIGHT
LOCK
H M