Casablanca Fan Company Victorian Ceiling Fan 63XXT - Manual (Page 8)

8
Inteli•Touch
®
R
R
R
Programmed into every Inteli-Touch Series fan is an Automatic
Demonstration Program. It can be used to fully demonstrate and
test the operation of the fan.
To enter the demonstration program:
1. Turn POWER off for at least three seconds. This will clear
the fan memory ready for programming.
2. Turn POWER on.
3. Immediately operate the buttons in the following sequence:
A multi-tone signal will verify the start of the test program which
proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will continue
to repeat until the POWER is turned off for more than three
seconds, cancelling the program.
The POWER button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light
level.
There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled . The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the button is used. To maintain this level of speed,
turn the fan on by pressing less than one second. To lower speed,
turn fan off, then on by pressing and holding the button until the
desired speed is reached. When the fan is on, you may increase the speed by
pressing and holding the button until the desired speed is reached,
then release it.
The direction of airflow can be changed from downward to
upward or from upward to downward.
To reverse the airflow:
1. Make sure the is on.
2. Press the button.
Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
LIGHT CONTROL
ON - OFF
A momentary press of
the LIGHT button
TO CHANGE BRIGHT-
NESS
PRESS AND HOLD
LIGHT BUTTON
LONGER THAN ONE
SECOND
To turn the lights off and on, press and release the button for less
than one second.
To vary the light brightness:
1. With lights off, press and hold the button. After one second the
lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
on at the same brightness the next time the button is used. To
maintain this level of brightness, press the button for less than
one second. To lower the brightness, turn the lights off, then press and hold
the button until the desired brightness level is reached. When the
light is on, you may increase the brightness level by pressing and holding
the button until the desired level is reached, then release it.
FAN CONTROL
ON - OFF
A momentary press
of the FAN button
TO CHANGE SPEED
Press and hold FAN
button longer than
one second
INTELI•TOUCH OPERATION POWER
INTELI•TOUCH OPERATION SPEED CONTROL
INTELI•TOUCH • REVERSING AIRFLOW
INTELI•TOUCH LIGHT
AUTOMATIC DEMONSTRATION PROGRAM
FAN
FAN
+ + + +
FAN LIGHT FAN LIGHT FAN FAN
LIGHT
FAN
FAN
FAN
FAN
FAN
REVERSE
LIGHT
LIGHT
LIGHT
LIGHT
LIGHT
R
POWER
POWER
POWER
R