Document Outline

• CRRFTSMflN
  • TABLE OF CONTENTS
  • INTRODUCTION
  • ák WARNING
  • A WARNING
  • CAUTION
    • Preparing your garage door
  • A WARNING
  • CAUTION
    • Tools needed
    • Planning
      • SECTIONAL DOOR INSTALLATIONS
    • Planning (Continued)
    • Assemble the Rail and Attach the Cable Pulley Bracket
      • To avoid installation difficulties, do not run the
    • ASSEMBLY STEP 2
      • Install the Trolley
    • ASSEMBLY STEP 3
      • Attach the Rail to the Motor Unit
        • To avoid installation difficulties, do not run the garage door opener until instructed to do so.
      • Install the Chain/Cable
      • and Attach the Sprocket Cover
        • INSTALLING THE CHAIN/CABLE
        • ATTACHING THE SPROCKET COVER
      • Tighten the Chain and Cabie
    • INSTALLATION
      • Determine the Header Bracket Location
      • Install the Header Bracket
        • WALL HEADER BRACKET INSTALLATION
        • CEILING HEADER BRACKET INSTALLATION
      • Attach the Rail to the Header Bracket
    • INSTALLATION STEP 4
      • Position the Opener
        • SECTIONAL DOOR OR ONE-PIECE DOOR WITH
        • TRACK
        • ONE-PIECE DOOR WITHOUT TRACK
      • Hang the Opener
    • INSTALLATION STEP 6
      • Install the Door Control
      • Install the Light
    • INSTALLATION STEP 8
      • Attach the Emergency Release Rope and Handle
      • Electrical Requirements
        • To avoid Installation difficulties, do not run the opener at this time.
        • If permanent wiring is required by your local code, refer to the following procedure.
      • Install The Ptotectot System®
        • IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR
        • Facing the door from inside the garage
        • INSTALLING THE BRACKETS
        • Garage Door Track Installation
        • Figure 4
        • MOUNTING AND WIRING THE SAFETY SENSORS
        • ALIGNING THE SAFETY SENSORS
        • TROUBLESHOOTING THE SAFETY SENSORS
      • Fasten the Door Bracket
        • SECTIONAL DOORS
        • ONE-PIECE DOORS
      • Connect Door Arm to Trolley
        • SECTIONAL DOORS ONLY
        • ALL ONE-PIECE DOORS
    • ADJUSTMENT STEP 1
      • Adjust the UP and DOWN Travel Limits
        • HOW AND WHEN TO ADJUST THE LIMITS
    • ADJUSTMENT STEP 2
      • Adjust the Force
        • HOW AND WHEN TO ADJUST THE FORCES
    • ADJUSTMENT STEP 3
      • Test the Safety Reversal System
        • TEST
        • ADJUST
        • IMPORTANT SAFETY CHECK:
    • ADJUSTMENT STEP 4
      • Test the Protector System‘S
      • Using Your Garage Door Opener
      • Using the Wall-Mounted Door Control
        • THE DOOR CONTROL
      • To Open the Door Manually
  • A WARNING
    • CARE OF YOUR OPENER
      • LIMIT AND FORCE ADJUSTMENTS:
      • THE REMOTE CONTROL BATTERY
      • MAINTENANCE SCHEDULE
  • ik WARNING
    • HAVING A PROBLEM?
      • 2. My remotes will not activate the door:
      • 3. My door reverses for no apparent reason:
      • 5. My motor unit hums briefly:
      • Safety sensors wire open (broken or disconnected).
      • OR
        • Door control or wire shorted.
    • PROGRAMMING
      • To Add or Reprogram a Hand-held Remote Control
        • USING THE “LEARN” BUTTON
      • To Erase All Codes From Motor Unit Memory
      • To Add, Reprogram or Change a Keyless Entry PIN
        • OR
    • REPAIR PARTS
      • Rail Assembly Parts
      • Installation Parts
      • Motor Unît Assembly Parts
        • 139.53702
        • Emergency Key Release;
        • Premium Control Console:
        • 139.53681
        • 139.53680
        • Security+®3-Function Remote Control:
        • Security+®Compact 3-Funct!on Remote Control:
        • 139.53704
        • 8 (2.4 m) Foot Rail Extension
        • 139.53684
        • Multi-Function Keyless Entry:
        • 139.53705
        • 139.53589
        • 10 (3 m) Foot Rail Extension:
        • Support Brackets:
        • 139.53786
        • 139.53709
        • Plug-In Light Control:
        • Door Clearance Brackets:
    • WARRANTY
      • SEARS WARRANTY