Clarion DXZ275MP - Manual (Page 13)

Basic Operations
English
11
DXZ275MP/DXZ375MP
Sound Adjustment
You can adjust a sound effect or tone quality to
your preference.
● Setting the Z-Enhancer
This unit are provided with 3 types of sound
tone effects stored in memory.
Select the one you prefer.
∗
The factory default setting is “ OFF ”.
2-1. Select “ Z-EHCR ”.
3-1. Each time you press the [ w ] or [ z ]
button, the tone effect changes in the
following order:
“ EXCITE ” ↔ “ IMPACT ” ↔ “ B-BOOST ” ↔
“ OFF ”
EXCITE : bass and treble emphasized
mid deemphasized
IMPACT : bass and treble emphasized
B-BOOST : bass emphasized
OFF : no sound effect
When “EXCITE” is set:
3-2. Press the [ ] button.
3-3. Press the [ w ] or [ z ] button to adjust the
bass and treble in the range of +3 to –3.
∗
The factory default setting is “ 0 ”.
3-4. Press the [ ] button to return to previous
mode.
When “IMPACT” is set:
3-2. Press the [ ] button.
3-3. Press the [ w ] or [ z ] button to adjust the
bass and treble in the range of +3 to –3.
∗
The factory default setting is “ 0 ”.
3-4. Press the [ ] button to return to previous
mode.
When “B-BOOST” is set:
3-2. Press the [ ] button.
3-3. Press the [ w ] or [ z ] button to adjust the
bass in the range of +3 to –3.
∗ The factory default setting is “ 0 ”.
3-4. Press the [ ] button to return to previous
mode.
● Adjusting the bass
This adjustment can be performed only when
the Z-Enhancer is set to “
OFF ”.
2-1. Select “ BASS ”.
3-1. Press the [ w ] or [ z ] button to adjust the
bass.
∗
The factory default setting is “ 0 ”.
(Adjustment range: +8 to –8)
● Adjusting the treble
This adjustment can be performed only when
the Z-Enhancer is set to “OFF”.
2-1. Select “TREBLE”.
3-1. Press the [ w ] or [ z ] button to adjust the
treble.
∗
The factory default setting is “0”.
(Adjustment range: +7 to –7)
● Adjusting the balance
2-1. Select “BALANCE”.
3-1. Press the [ w ] or [ z ] button to adjust the
balance of the right and left speakers.
∗ The factory default setting is “CENTER”
(center). (Adjustment range: RIGHT12 to
LEFT12 (right 12 to left 12))
To change sound setting
1. Press the [ ] button to switch to the
sound adjustment selection display.
∗ The factory default sound setting is “Z-
EHCR”.
2. Then press the [ x ] or [ v ] button to
select the sound adjustment mode.
Each time you press the [ x ] or [ v ]
button, the sound adjustment mode
changes as following order:
“Z-EHCR” ↔ “BASS” ↔ “TREBLE” ↔
“BALANCE” ↔ “FADER” ↔ “REAR/S-W”
↔ “S-W VOL” ↔ “HPF”
The sound adjust mode will be display for
2 seconds before showing the sound
setting.
3. Press the [ w ] or [ z ] button to adjust the
selected audio mode.
∗
In the case of display blinking “ENT”, you
can press the [
] button to adjust the
setting value.
4. After completing settings, press the [ ]
button to return to the previous mode.
DXZ375MP_EN.book 11 ページ ２００６年１１月１０日 金曜日 午後１時１５分