ASKO T731 - Manual (Page 12)

DEAYED START
This option lets you set the dryer to start at the most
convenient time. This feature is also useful in areas
where utility companies offer discount rates during off­
peak hours. You can set delayed start from 1 hour to 24
hours, in one-hour increments.
To set a delayed start time, press the button until the
number of hours you wish to delay starting the machine
displays on the LED, as illustrted below:
If you pass the time you wanted to select, continue to
press the button until the correct time displays. If you
decide not to delay starting the unit, continue to press
the button until “0” displays.
Press Start and the unit will start after the number of
hours you selected has passed.
To cancel Delay Start after you have pressed the Start
button, press and hold the Stop button until the LED
displays the program number or, if the program knob is
set on 5 or 6, the number of minutes. You can then press
Start and the unit will start right then.
TEMPERAURE CONTROL
(^)
You have two temperature options: Normal and Low. The
Normal setting should be used for heavier fabrics, such
as denim, cotton, linen, etc. The Low setting should be
used for lighter, more delicate fabrics, such as synthetics,
permanent press, acrylics, etc.
The indicator light will stay lit when Low is selected. It will
remain offwhen Normal is selects.
BUZZER■
Press this button to set a buzzer to sound for three
seconds when the program is complete. The indicator
light will stay lit when this option is on.
If you selected the Anti-crease option, the buzzer will
sound every time the drum rotate.
COOL-DOWN
®
Every program, except Air Fluff, ends with a cool-down
cycle that tumbles the clothes without heat to reduce
wrinkling. The Cool-down button lets you choose between
the Normal cool-down cycle (15 minutes) or a Quick
cool-down cycle (5 minutes). The indicator light will stay
lit when Quick is selected.
CHANGING OPTION SETTINGS
You cannot change the option settings after you have
pressed Start. To change a setting, hold down the Stop
button until the unit stops, make your change, then
press Start again. The program will restart from the
beginning.
PROGRAM MEMORY
The dryer is designed to retain the settings last selected
with each program. For example, if you select Normal
Dry, the Low temperature option, a 2-hour anti-crease,
and Quick cool-down, next time you select Normal Dry
these options will automatically be selected.
PROGRAMS
Your ASKQ dryer has our state-of-the-art Sensidry
system. This means it has a humidity sensor that ensures
different fabrics always dry thoroughly. This sensor turns
off the heat when the laundry has reached the appropriate
dryness.
The Extra Dry, Dry, Normal Dry, and Iron Dry programs
are automatic (thermostat-controlled) programs designed
for certain types of loads, as defined in the table below.
The sensor detects different levels of humidity with
each program. It is important, therefore, to select the
appropiate program for the type of load you are drying.
If you prefer, you can select Timed Dry, which does not
activate the humidity sensor. You should be careful when
using this option not to overdry the fabrics. This program
automatically uses the Low temperature setting, but you
can change it to Normal by depressing the Temperature
button.
When using Timed Dry, it’s best to use a shorter time;
then if the load isn’t dry, you can set the timer for a few
more minutes.
NOTE: Always follow the care label instruction. (See
page 10.)
Program Definition
Extra dry (PI) For items that are extremely difficult to dry, such as jeans and thick towels.
Dry (P2) Cotton w/out elastic and/or decorative trim.
Normal dry (P3) Cotton with elastic and/or decorative trim, linen (white and colorfast).
Iron dry (P4) Synthetics, polyester, cotton/polyester blends.
Timed Dry Anv fabric that can be machine dried. (See note below.)
Air Fluff This setting does not heat. It simply circulates the air as the clothes tumble to shake out the
dust and refresh the clothes. (See note below.)
NOTE: When using Timed Dry and Air Fluff, you must set the number of minutes for the program to run. (See “Time”
on page 11 for details.)
Page 12