Autostart AS-2460 - Manual (Page 10)

• Press and release the JEI button and you will hear a beep. L-01 will appear on the display. Then
press the ^ button for 3 seconds (the parking lights will flash once).
When the system exits cold weather mode, the remote control will beep once and the (^icon will
disappear.
To verify whether the system is in coid weather mode:
Press the brake pedal: If the vehicle is in cold weather mode, the parking lights will stay on while
the pedal is pressed.
How to access cold weather mode
Function Button pressed Icon Sound Instructions /description
To enter cold
weather mode
mA p)
Beep
Press El and the press and
To exit cold weather
mode
mA
None Beep hold f for 3 seconds.
Extended Run Time
While the vehicle is running under a remote start, pressing and holding the button for more
than 3 seconds will reset the run time counter to zero and restart the run time cycle from the
beginning. There will be one beep —a pause— three more beeps; the parking lights will flash
three times and the horn (if configured) will honk once. The extended run time procedure can
only be carried out once per remote start.
To stop the vehicle, at any moment, simply press the ^ button.
Example: If your remote car starter is programmed for a run time of 3 minutes and your vehicle
has been running for 2 minutes already, pressing the ^ button will reset the counter
to zero and allow the engine to run for another cycle (in this case, 3 minutes).
i_Advance_d_Featu_res: lnst_allation-progjammable Optjons_______
The remote car starter was designed with flexibility in mind. With its programmable options, this
unit can single-handedly control nearly any electrical system in your vehicle.____________________
Caution : The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your Remote Car Starter.
Remote Door Locks
If your Remote Car Starter was installed with the Remote Door Locks option, you will have the
convenience of remote keyless entry. See section Arming the Starter Kiii, earlier in this Guide, for
further instructions on remote door locking and unlocking.
Priority Door Access
If the Remote Door Locks option is installed on your vehicle, this safety feature allows you unlock
solely the driver's door with a single press of the unlock button on the transmitter; upon a second
press of the unlock button, all the other doors will unlock.
Ignition-controlled Door Locks
This is an added security feature. If your Remote Car Starter was installed with the Ignition-
Controlled Door Locks option, the doors will automatically be locked as soon as the ignition key is
turned to the ignition on ( run ) position while the brakes are pressed. When the key is turned to the
off position, the doors will automatically be unlocked.
P. 10 User Guide
Ignition Re-lock
On Remote Car Starters of this series, when Ignition-controlled Door Locks are enabled and the
ignition key is in the ignition on ( run ) position, should any door be unlocked and opened, all doors
will be relocked next time the brake pedal is pressed.
Secure Lock
Before it can remote-start your vehicle, the Remote Car Starter must first disarm the factory
security system. The Secure Lock feature may be required on certain vehicle models with factory
security systems that automatically unlock the doors when the security system is disarmed.
To keep your vehicle protected when the factory security system is disarmed for a remote start,
Secure Lock will relock your doors as soon as the vehicle has started. Once the engine run cycle
ends, Secure Lock will rearm your factory security system.
Remote Trunk Release
If your system was installed with the remote trunk release option, you can open your trunk by
pressing the trunk button for 3 seconds.
The Starter Kill and the Anti-grind Feature
With this added security feature, the system will prevent your vehicle from starting with the ignition
key when the Starter Kill is armed. If your Remote Car Starter was installed with the Starter Kill
option, one will not be able to start your vehicle with the key unless the system has been unlocked
and disarmed first, or put into Valet Mode.
Note: If the Starter Kill is installed, your vehicle will benefit from a protection against starter
motor damage that could occur after remote-starting the engine should the user, by force of
habit, turn the ignition key to the crank position.
Safe Start
If this feature is enabled, the user must press the start / stop button 2 times within 3 seconds to
remote-start the vehicle. This will eliminate accidental remote starts, e.g. when children are playing
with the transmitter.
1. Press and release the start / stop button.
The parking iights wiii turn on.
2. Within 2 seconds of the parking lights turning on, press and release start / stop again (before
the parking lights turn off).
If Swap Start Mode is selected, to remote-start your vehicle press Band then lock . The aux 2
output can be activated by pressing the start / stop button.
Installer-Programmable Valet Modes
Valet Mode Using the Valet Switch (if installed)
To put the system i n t o Vaiet Mode:
• Turn the ignition key to the ignition on ( run ) position.
• Within 3 sec., press the valet button, the parking lights will flash three times and the
L.E.D. will come on solid once the ignition key is removed.
To take the system out of Vaiet Mode:
• Turn the ignition key to the ignition on ( run ) position.
• Within 3 sec., press and release the valet button , the parking lights will flash twice
the L.E.D. will turn itself off.
Note: Once Valet Mode is activated, the remote starter will be disabled.
"Home ValetTM" Mode
If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if
the vehicle is parked indoors there is no danger of it starting accidentally by remote control.
User Guide P. 11