Autostart AS-2460 - Manual (Page 8)

• To disarm the starter kill, press the ^ button on the transmitter.
The parking lights will flash twice.
If remote door locks are installed, this will also unlock the doors.
• To arm the Starter Kill, press the S button on the transmitter.
The parking lights will flash once.
If remote door locks are installed, this will also lock the doors.
• In passive mode, the starter kill will automatically arm if the ignition key is not inserted
into the ignition switch within 1 or 3 minutes after unlocking (the key sense feature
must be installed).
Remote Starter Features
Idle Mode
Convenience feature: Idle Mode allows you to keep the engine running and the doors
locked while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the
Ignition Switch) while the engine is running. For example, if you stop for a delivery or at a conveni­
ence store, lock your vehicle and leave it running for the length of a run cycle while you are away.
The engine will go on running until the user re-enters the vehicle or until the expiration of the
Engine Run Time.
Idle Mode can be activated through the same routine as that used for Ready Mode; at the last step,
the button is pressed instead of the other buttons:
1. Ensure that all the Doors are closed and that the Shifter is in the Neutral position.
2. With the Engine already running, apply the Parking Brake and release the Brake Pedal.
Make sure to release the brake pedal.
3. Within 20 sec. push SI, Sor ‘ij on the Transmitter.
The parking lights will flash 3 times quickly and remain lit.
4. Remove the key: the Engine will go on running.
5. Exit the vehicle and close the Door.
6. Press the button until the system is armed (the doors will be locked if remote door
lock is installed).
If the pre-programmed run-time expires or if the user shuts down the engine by remote control, the
vehicle will get in Ready Mode.
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.
Valet Modes
Ignition Valet
This feature will allow you to remotely put your system into valet mode by using the ignition key
instead of the valet button as above. Ignition valet can be used without a valet button installed.
To put the system i n t o valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times successively into
the IGNITION ON; run and off positions.
The parking lights will flash three times to indicate that the vehicle is now in valet mode. The L.E.D.
will come ON solid.
— The
El
icon will appear on your LCD remote if you press lock or unlock ..
To take the system out of valet mode:
Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times successively into
the IGNITION ON; run and off positions.
The parking lights will flash twice to indicate that the vehicle is now out of valet mode. The L.E.D.
will go out.
P. 8 User Guide
Flashing LED off : the LED will not flash even when the module is armed (either under active or
passive arming). Nevertheless, if the module enters valet mode, the LED will still remain lit
without flashing as long as the ignition is off.
Multi-car Operation
This option allows the owner of two vehicles, both equipped with the same Remote Car Starter
model, to control both systems with a single remote control. To control the second vehicle:
Press trunk + LOCK buttons simultaneously:.................................................... lock
Press trunk + unlock simultaneously:............................................................... unlock
Press trunk + start ; stop simultaneously:........................................................ start
Press TRUNK + START/STOP simultaneously:................................................. stop
Press
or
Press
Press
Press
Press
Press
J >
> TRUNK:.............................................................................. TRUNK
lock :................................................................................... LOCK E>l
m > m > unlock : .................................................................................. UNLOCK
m > m > START/STOP:............................................................................ START
> START/STOP:.....................................................................STOP
E> E > TRUNK:......................................................................................... TRUNK
Note: In order to access the 2 nd car operations with the companion remote, Shift button must
be pressed twice quickly and then one more time followed by lock , unlock , trunk or
start / stop . If the multi-level features have been modified from their default state by your
installer, the shift button may have to be pressed once, twice or three times, according to the
option you chose.
LCD Transmitter Operation and Confirmations (Second Car Control)
Basic Operations
Function Button press Icon Sound
Lock
Ü
1 beep
Unlock
D
2 beeps
Start Melody
Stop None Melody
Trunk E > E > l i 1 Beep
start/stop While in Safe Start Mode
Function Button press Icon Sound Description
Start on safe start
mode
Melody
Press ^
simultaneously twice within 3
seconds. Press for 1 sec- a beep
will be heard- then press 1 sec
and a melody will be heard
again.
Stop on safe start
mode
None Melody
User Guide P. 13