Angelcare AC403 - Manual (Page 9)

5.1 - MENU ACCESS AND CHANGING THE SETTINGS
STEP 5 - TESTING AND GETTING TO KNOW YOUR MONITOR
The Angelcare ® monitor can be used with the pre-program factory settings
or you can also customize your settings to your preference.
The MENU settings are accessed by using the MENU button on the Parent Unit.
The MENU functions are in a loop. Each time you press the menu button briefly you
move on to the next MENU function. The MENU functions are in the following order:
PRESS 1 TIME: ‘TIC’, Movement & Sound ......................... STEP 5.2 & STEP 5.3
PRESS 2 TIMES: Out of Range................................................. STEP 5.4
PRESS 3 TIMES: Sound Transmission .......................................... STEP 5.5
PRESS 4 TIMES: Alarm ........................................................ STEP 5.7
PRESS 5 TIMES: Temperature ................................................. STEP 5.9
All changes and adjustments
made in the main menu
and sub-menu will not be
activated unless you confirm
them by pressing the
SELECT button followed by
the
EXIT button.
NOTE:
By continuing to press the MENU button you will
be continuously moving through the loop. Once
you have selected your preferred settings you
must press SELECT and then EXIT or your changes
will not be saved.
5.2 - SENSOR PAD
SENSOR PAD FUNCTIONS:
‘ TIC’: Allows you to detect baby’s
movements as well as hear a TIC sound
at each movement. (This function can
ONLY be activated in conjunction with
the Movement Function).
Sound Only: Allows you to detect
the baby’s sounds ONLY. Movement
detection will be deactivated.
Movement Only: Allows you to detect the
baby’s movements with the TIC sound.
IMPORTANT
When in MENU or SUB-MENU mode
NO sound, alarm or vibration will be
emitted from either the Parent Unit
or the Nursery Unit even if they were
activated before pressing the MENU
or SUB-MENU mode.
IF THE ALARM DOES NOT SOUND
• Avoid contact with crib while Sensor Pad is in operation.
• Place crib near a supporting wall.
• Adjust Sensor Pad sensitivity level.
5.3 - CHANGING THE MOVEMENT AND SOUND MONITORING FUNCTIONS
1) Press the MENU button once and
the flashing icons will appear.
2) Use the UP and DOWN Arrows to select
your preferred detection mode.
3) Press the SELECT button to confirm
your choice.
4) Press the MENU to view the next option,
or EXIT if you wish to stop programming.
1) Move your hand lightly on the mattress.
Pendulum icon will appear
on Parent Unit indicator bar.
It will move as you move your
hand and trigger a ‘TIC’ sound.
2) Remove your hand from the mattress.
After 15 seconds you will hear a
‘TIC’ pre-alarm sound, and 5 seconds
later the Movement Alarm will trigger.
3) Repeat by moving your hand lightly
in all four corners of the mattress.
Ensure the Nursery Unit Movement
Indicator is still flashing.
1 2
TO SET DETECTION MODE:
TO TEST THE SENSOR PAD:
movement or “tic” mode need to be activated:
MOVEMENT ALARM
• If NO movement is detected after 15 seconds you will hear a single ‘TIC’ pre-alarm sound from
the Nursery Unit.
• If after a further 5 seconds there is still NO movement detected both the Parent Unit and Nursery
Unit speakers will emit loud warning sound.
• Nursery Unit icon flashes on the Parent Unit
• Green light on the Nursery Unit will turn off to indicate NO movement is being detected.
3
2
1
If you press the MENU button for too long
the unit will go in to connection mode and the
Out-of-Range indicator will start flashing. If this
happens, wait 20 seconds and then press
the
MENU to start again.
Movement Only
Sound Only
‘TIC’, Sound & Movement
Sound & Movement
‘TIC’ & Movement
IMPORTANT
When in MENU or SUB-MENU modes,
sound transmission between Parent
and Nursery Units will be temporarily
deactivated.
17 16