Maintenance and service – EZ-ACCESS PASSPORT User Manual
Page 4
Page 4 of
26
around the VPL of a procedure or potential hazard resulting in an unsafe operating condition which could lead
to severe injury or fatality of occupant and or others. Refer to section 4 for images of the labels that should be
found on the VPL. Maintaining all labels and manuals in legible condition is required by the VPL owner and is
essential for safe VPL operation. Contact your dealer for additional information, for replacement labels and
manuals, or to schedule any needed inspections, repairs or service.
Illumination: A minimum illumination at the landing edge of the floor with the landing door open of not less than
50 Ix (5 fc).
Illumination of at least 100 lx shall be provided:
(a) at the drive unit in the location where periodic maintenance and inspection are required;
(b) on the carriage at the seat or platform surface and at the operating devices; and
(c) at the floor level of landing/loading points.
For proper warranty coverage, contact your dealer.
Keep all protective coverings in place, unless servicing the VPL.
The VPL warranty is not transferable.
Attempting to tamper with or modify any portion of the VPL will void your warranty.
Except as described elsewhere in this manual, maintenance must only be performed by qualified technicians.
Contact your dealer to schedule any needed inspections, repairs or service.
Caustics, high alkaline detergents and solutions should not be used to clean aluminum.
1. Except as described elsewhere in this manual, maintenance must be performed
only by qualified
technicians. Contact your dealer with questions or to schedule any needed inspections, repairs or service.
2. Annual inspections by a qualified technician are highly recommended to help prevent unsafe conditions
and operation. Contact your dealer with questions or for additional information, to request replacement
labels or manuals, or to schedule any needed inspections, repairs or service.
3. A visual inspection of all bolts and nuts to be sure that they are securely in place must be done by the user
before using. If there are any missing or damaged fasteners or other components, they need to be
replaced by a qualified technician to ensure continued safe operation.
Contact your dealer with questions
for additional information, to request replacement labels or manuals, or to schedule any needed
inspections, repairs or service, or call our Customer Service line at 1-800-451-1903, or visit us on the
internet at
There are two holes in the tower used for mounting the guard ramp activating bar which do not have
fasteners in them. This is normal since the guard ramp activating bar can be mounted on either side.
4. Keep the VPL platform free of debris. Sweeping to clear these areas regularly enough to prevent debris
accumulation is required. Wiping with a damp cloth should be sufficient for additional surface cleaning. If
needed, a soft brush with mild soap and water can be used on the platform and guard ramp surfaces.
Alkaline based detergents should not be used to clean your VPL.
5. If the platform and guard ramp surface are covered with frost, ice and or snow, remove frost, ice and or
snow before using the VPL.
Calcium chloride is often used to deice and prevent ice from forming on roads. Used properly,
this may be useful to help rid or keep your VPL platform free of frost, ice and snow.
If using a deicing or ice preventing agent, such as Calcium chloride, always check that
the platform is free of ice before using it. Calcium chloride may not always be effective in
removing frost, ice and or snow.
If the VPL was cleaned with soap, rinse all soap from VPL and let VPL dry before using.
Use extra caution while on the VPL platform and guard ramp surfaces are icy or wet.
If cleaning with water, turn off VPL and unplug the AC power before cleaning.
6. Periodically check and ensure that the safety pan under the platform moves freely up and down and is not
damaged. This is the built in safety device designed to detect obstructions under the platform and stop
platform downward motion.
Do not operate VPL if the safety pan is malfunctioning. Contact your dealer immediately, or call
our Technical Support line at 1-800-332-1381, or visit us on the internet at