Artesyn ATCA-7365 Installation and Use (May 2014) User Manual
Atca-7365
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- ATCA-7365
- Contents
- About this Manual
- Safety Notes
- Sicherheitshinweise
- Introduction
- Hardware Preparation and Installation
- Controls, Indicators, and Connectors
- BIOS
- 4.1 Introduction
- 4.2 Accessing the Blade Using the Serial Console Redirection
- 4.3 Changing Configuration Settings
- 4.4 Boot Options
- 4.5 BIOS Setup Configuration
- 4.5.1 Main
- 4.5.2 Advanced
- 4.5.2.1 Advanced -> CPU Configuration
- 4.5.2.2 Advanced -> Memory Configuration
- 4.5.2.3 Advanced -> Chipset - North Bridge
- 4.5.2.4 Advanced -> Chipset - South Bridge
- 4.5.2.5 Advanced -> SATA Configuration
- 4.5.2.6 Advanced -> USB Configuration
- 4.5.2.7 Advanced -> Super IO Configuration
- 4.5.2.8 Advanced -> Serial Port Console Redirection
- 4.5.2.9 Advanced -> UEFI Network Stack
- 4.5.2.10 Advanced -> Runtime Error Logging
- 4.5.2.11 Advanced -> SMBIOS Event Log
- 4.5.2.12 Advanced -> Local IPMI System Event Log
- 4.5.2.13 Advanced -> WHEA Configuration
- 4.5.3 IPMI
- 4.5.4 iSCSI
- 4.5.5 Boot
- 4.5.6 Security
- 4.5.7 Save & Exit
- 4.6 CPU Performance Settings
- 4.7 Memory Configuration
- 4.8 Restoring BIOS Default Settings
- 4.9 Support for 200 Watt Slots
- 4.10 LED Usage
- 4.11 Upgrading the BIOS
- 4.12 BIOS Error Logging
- 4.13 BIOS Status Codes
- Functional Description
- 5.1 Block Diagram
- 5.2 Processor
- 5.3 Memory
- 5.4 Chipset
- 5.5 I/O Controller
- 5.6 Firmware Flashes
- 5.7 Ethernet Ports
- 5.8 Storage Controller
- 5.9 Embedded Flash Disk
- 5.10 BIOS
- 5.11 IPMC
- 5.12 Serial Redirection
- 5.13 Serial over LAN
- 5.14 Control Logic
- 5.15 Front Board Face Plate
- 5.16 USB 2.0 Interface
- 5.17 SMBus Interface
- 5.18 Real Time Clock
- 5.19 VGA Module
- Maps and Registers
- 6.1 Interrupt Structure
- 6.2 PCI Express Port Mapping
- 6.3 Registers
- 6.4 FPGA Register Mapping
- 6.4.1 LPC I/O Register Map
- 6.4.2 IPMC SPI Register Map
- 6.4.3 Module Identification Register
- 6.4.4 Version Register
- 6.4.5 Serial Redirection Control Register
- 6.4.6 Serial over LAN (SOL) Control Register
- 6.4.7 Serial Line Routing Register
- 6.4.8 IPMC Power Level Register
- 6.4.9 SPD PROM MUX Control Register
- 6.4.10 Reset Registers
- 6.4.10.1 BIOS Reset Source Register
- 6.4.10.2 Reset Mask Register
- 6.4.10.3 BIOS IPMC Watchdog Timeout Register
- 6.4.10.4 BIOS Push Button Enable Register
- 6.4.10.5 OS Reset Source Register
- 6.4.10.6 OS IPMC Watchdog Timeout Register
- 6.4.10.7 IPMC Watchdog Timeout Register
- 6.4.10.8 IPMC Reset Source Register
- 6.4.11 RTM SPI Interface Registers
- 6.4.12 Interrupt Control and Status Registers
- 6.4.13 Flash Status and Protection Registers
- 6.4.14 BIOS Boot Mode Register
- 6.4.15 SFMEM Module Configuration Register
- 6.4.16 Update Channel Equalization Control Register
- 6.4.17 IPMC E-Keying Status Register
- 6.4.18 IPMC E-Keying Control Register
- 6.4.19 IPMC GPIO Register
- 6.4.20 LED Status and Control Register
- 6.4.21 NMI Status and Control Register
- 6.4.22 Telecom Clock Supervision Registers
- 6.4.23 Miscellaneous Status/Control Registers
- 6.4.24 Scratch Registers
- Serial Over LAN
- Supported IPMI Commands
- 8.1 Standard IPMI Commands
- 8.2 PICMG 3.0 Commands
- 8.3 Artesyn Embedded Technologies Specific Commands
- 8.4 Pigeon Point Specific Commands
- 8.4.1 Get Status Command
- 8.4.2 Get Serial Interface Properties Command
- 8.4.3 Set Serial Interface Properties Command
- 8.4.4 Get Debug Level Command
- 8.4.5 Set Debug Level Command
- 8.4.6 Get Hardware Address Command
- 8.4.7 Set Hardware Address Command
- 8.4.8 Get Handle Switch Command
- 8.4.9 Set Handle Switch Command
- 8.4.10 Get Payload Communication Time-Out Command
- 8.4.11 Set Payload Communication Time-Out Command
- 8.4.12 Enable Payload Control Command
- 8.4.13 Disable Payload Control Command
- 8.4.14 Reset IPMC Command
- 8.4.15 Hang IPMC Command
- 8.4.16 Graceful Reset Command
- 8.4.17 Get Payload Shutdown Time-Out Command
- 8.4.18 Set Payload Shutdown Time-Out Command
- 8.4.19 Get Module State Command
- 8.4.20 Enable Module Site Command
- 8.4.21 Disable Module Site Command
- 8.4.22 Reset Carrier SDR Repository Command
- FRU Information and Sensor Data Records
- Firmware Upgrade
- A Replacing the Battery
- B Related Documentation