Artesyn ATCA-7470 Installation and Use (October 2014) User Manual
Atca-7470
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- ATCA-7470
- Contents
- About this Manual
- Safety Notes
- Sicherheitshinweise
- Introduction
- Hardware Preparation and Installation
- Controls, Indicators, and Connectors
- BIOS
- 4.1 Introduction
- 4.2 Accessing the Blade Using the Serial Console Redirection
- 4.3 Changing Configuration Settings
- 4.4 Boot Options
- 4.5 IPMI Boot Parameter
- 4.6 Restoring BIOS Default Settings
- 4.7 BIOS Setup Configuration
- 4.8 Restoring BIOS Default Settings
- 4.9 IPMI Support
- 4.10 Watchdog Support
- 4.11 BIOS Error Logging
- 4.12 LED Usage
- 4.13 Upgrading the BIOS
- 4.14 BIOS Status Codes
- Functional Description
- 5.1 Block Diagram
- 5.2 Processor
- 5.3 Memory
- 5.4 Platform Controller Hub (PCH)
- 5.5 Firmware Flashes
- 5.6 Ethernet Ports
- 5.7 Storage Controller
- 5.8 MO297 SlimSATA Embedded Solid State Disc (SSD)
- 5.9 BIOS
- 5.10 IPMC
- 5.11 Serial Redirection
- 5.12 Serial Over LAN
- 5.13 Control Logic
- 5.14 Front Board Face Plate
- 5.15 Faceplate Serial Interfaces
- 5.16 USB 2.0 Interfaces
- 5.17 LPC Interface
- 5.18 Trusted Platform Module
- 5.19 Real Time Clock
- 5.20 ATCA-7470 Accelerator Module Slot
- 5.21 SMBus
- Maps and Registers
- 6.1 Interrupt Structure
- 6.2 FPGA Registers
- 6.3 Registers
- 6.4 FPGA Register Mapping
- 6.4.1 LPC I/O Register Map
- 6.4.2 IPMC SPI Register Map
- 6.4.3 Module Identification Register
- 6.4.4 Version Register
- 6.4.5 Serial Redirection Control Register
- 6.4.6 Serial over LAN (SOL) Control Register
- 6.4.7 Serial Line Routing Register
- 6.4.8 RTM SPI Interface Registers
- 6.4.9 DIMM ADR Status Register
- 6.4.10 Reset Registers
- 6.4.10.1 BIOS Reset Source Register
- 6.4.10.2 Reset Mask Register
- 6.4.10.3 BIOS IPMC Watchdog Timeout Register
- 6.4.10.4 BIOS Push Button Enable Register
- 6.4.10.5 OS Reset Source Register
- 6.4.10.6 OS IPMC Watchdog Timeout Register
- 6.4.10.7 IPMC Watchdog Timeout Register
- 6.4.10.8 IPMC Reset Source Register
- 6.4.10.9 DIMM ADR Configuration Register
- 6.4.10.10 Software Reset Register
- 6.4.10.11 FWH_PLTRST_ Enable Register
- 6.4.11 Interrupt Control and Status Registers
- 6.4.12 PCI Express Hot Plug I2C IO Expander Registers
- 6.4.13 Flash Status and Protection Registers
- 6.4.14 BIOS Boot Mode Register
- 6.4.15 Update Channel Equalization Control Register
- 6.4.16 IPMC E-Keying Status Register
- 6.4.17 IPMC E-Keying Control Register
- 6.4.18 LED Status and Control Register
- 6.4.19 CPLD Revision Register
- 6.4.20 Spare Signals Status Registers
- 6.4.21 DIMM Event Register
- 6.4.22 CPU Type and Presence Detection Register
- 6.4.23 Memory Temperature Status Register
- 6.4.24 Base Interface link Status Signals Register
- 6.4.25 Miscellaneous Status/Control Registers
- 6.4.26 Telecom Clock Control and Supervision Registers
- 6.4.27 Serial Management Interface (MII) Control Registers
- 6.4.28 Scratch Registers
- Serial Over LAN
- Boot Bank Selection
- Supported IPMI Commands
- 9.1 Standard IPMI Commands
- 9.2 PICMG 3.0 Commands
- 9.3 Artesyn Specific Commands
- 9.4 Pigeon Point Specific Commands
- 9.4.1 Get Status Command
- 9.4.2 Get Serial Interface Properties Command
- 9.4.3 Set Serial Interface Properties Command
- 9.4.4 Get Debug Level Command
- 9.4.5 Set Debug Level Command
- 9.4.6 Get Hardware Address Command
- 9.4.7 Set Hardware Address Command
- 9.4.8 Get Handle Switch Command
- 9.4.9 Set Handle Switch Command
- 9.4.10 Get Payload Communication Time-Out Command
- 9.4.11 Set Payload Communication Time-Out Command
- 9.4.12 Enable Payload Control Command
- 9.4.13 Disable Payload Control Command
- 9.4.14 Reset IPMC Command
- 9.4.15 Hang IPMC Command
- 9.4.16 Graceful Reset Command
- 9.4.17 Get Payload Shutdown Time-Out Command
- 9.4.18 Set Payload Shutdown Time-Out Command
- 9.4.19 Get Module State Command
- 9.4.20 Enable Module Site Command
- 9.4.21 Disable Module Site Command
- 9.4.22 Reset Carrier SDR Repository Command
- FRU Information and Sensor Data Records
- Firmware Upgrade
- A Replacing the Battery
- B Related Documentation