Bompani BO243OG/E - Manual (Page 30)

30
For the user GB
operation of the oven (using push knob and indicator icons).
Pushing on the the knob, you can: adjust the time, program the
start time and end of cooking, set the alarm (Minute Minder).
SETTING TIME
To adjust the clock press the knob briefly 4 times until you get
the flashing of the “CLOCK” icon. Hence to increase or decre-
ase the time, turn knob clockwise or counterclockwise. After 10
seconds of the last adjustment the electronic timer automatically
exit time setting mode.
MANUAL COOKING
During default condition, timer allows manual firing of the oven
using the general oven switch (external to the timer).
PROGRAMMING END COOKING TIME
Cooking end programming allows you to start immediately
and stop cooking in an automatic manner based on the time
scheduled. To program the end of cooking time briefly press 2
times the knob until you get the flashing of “END TIME” icon. To
increase or decrease the cooking time, turn knob clockwise or
counterclockwise. The flashing of “END TIME” icon continues
for some seconds after the last rotation. The program can be
confirmed by pressing the knob (at least 2 minutes
of cooking time). Upon confirmation of the program, the cooking
is started and the alarm is automatically activated.
Cooking stops when “Programmed End Time = Present
Time”. To view the program press and release the knob and
the timer show the selected program. When cooking stops the
“END TIME” icon flashes and the alarm beeps. After 1 minute
beeps are disabled and the icon “END TIME” remains flashing
until you press the knob.
To cancel the program before the end, press the knob for some
seconds and the program will be canceled and the timer returns
to manual cooking mode.
START AND END COOKING TIME PROGRAMING
Cooking start programming allows to start end stop cooking
automatically based on the time scheduled. To program the co-
oking start time, briefly press 1 time the knob until the flashing of
the “START TIME” icon. Increase or decrease the cooking start
time turning knob clockwise or counterclockwise. The flashing of
“START TIME” icon continues for some seconds after the last
rotation. If within this time you don’t turn or press the knob the
hands return automatically to display the time and the program is
canceled. If you press the knob the cooking start time is stored
(“START TIME” icon is turned on) and timer switches to cooking
end programming (the “END TIME “ icon from off becomes
flashing). The cooking time end programming will follow the
procedure in the preceding section. Cooking will begin when
“Programmed Start Time = Present Time”.
MINUTE MINDER PROGRAMMING
Minute Minder programming allows you to have a simple alarm
after a scheduled time without activating the cooking (mode
Minute Minder). To schedule an “alarm” (Minute Minder mode),
press the knob 3 times until the flashing of “ALARM” icon.
Minute Minder setting is identical to end of cooking time setting
(see the corresponding paragraph). It’s possible to use Minute
Minder only when there is no current cooking program active.
DISPLAYING THE PROGRAM SET
The timer allows the display of the program. To view the program
set press and release the knob, at the same time the program-
mer will display the program set by moving the hands on the set
times and highlighting the steps with the flashing of the icons.
The controller then returns automatically to display the current
time and continues with the execution of the program.
CANCELLATION OF PROGRAM SET
The timer allows the cancellation of the program. To delete the
program set to press knob for a few seconds until the icons shut
off and emission of the second beep.
The programmer then automatically returns to the manual
cooking.
BLACKOUT INDICATION
The timer signals every lack of power supply through the flashing of the symbol “CLOCK”. In this case, to disable it briefly press
the knob.
CLEANING THE OVEN
- The oven should be cleaned after each use, when it is still
lukewarm but not hot. This allows fats to be removed before
they have time to dry.
- If stubborn stains remain place a cloth soaked in ammonia
on the bottom of the oven, close the door and leave for a few
hours. Then wash the oven with hot water and liquid detergent
and dry completely.
- For the outside of the oven, use a soft cloth and soapy water.
NEVER USE POWDER DETERGENTS OR OTHER ABRASIVE
PRODUCTS.
FOR COOKERS WITH SELF-CLEANING OVEN
The two side walls and the back are coated with a catalytic self-
cleaning enamel ( fig. 5 ).Every 10-15 times it is used, leave the
oven empty at full heat. The time required for cleaning depends
on the condition of the oven. Some splashes tend to set hard
and may clog the pores of the special coating, preventing oxida-
tion and eliminating its self-cleaning properties. In this case, as
soon as the oven has completely cooled apply very hot water
to soften the deposits and use a soft brush, without detergent,
to remove them. Then switch the oven back on at maximum
heat for a few minutes.
Important: never use metal brushes or abrasive substances).
To replace the catalytic liners, purchase item code 0003103/I
CHANGING THE OVEN LIGHT BULB
- Switch the oven off and disconnect it from the mains electrical
supply;
- the light bulb is in the top right-hand corner of the back of the
oven;
- make sure that the oven is cold and unscrew the glass lamp-
holder;
- replace the light bulb with another of the same type and screw
the lamp-holder back firmly into place.
REMOVING THE OVEN DOOR
The door can be removed to clean the oven in an easier way
following this instructions:
1) Open the door completely.
2) Turn the two levers “B” bringing them from position 1 to po-
sition 2 (see fig.11).
3) Close the door slowly to a stop, grab it with both hands from
side to side, close it further and pull it by lifting it upwards.
4) To replace the door you must follow the procedure in reverse
order, insert the two hinges in their seats and open the door
completely.
5) Turn the two levers “B” bringing them back in position 1.
6) Close the door normally.
CLEANING THE DOOR GLASS
All ovens are fitted with glass doors with innovative, extremely
convenient characteristics. The full-glass on the inside can be
removed easily without the aid of any tools: the screw-free vi-
sible fixing system guarantees that the door provides the easy
cleaning only glass can ensure. Proceed as follows to remove
the glass in the oven door correctly.
- Fully open the door;
- apply gentle leverage with a coin or a flat-head screwdriver
in the two recesses in the bottom of the inside of the door si-
multaneously;
- released from its seat, the glass can be extracted from the
recess into which it is fitted:
- After cleaning, repeat the same procedure in reverse order.
WARNING:Take care to reassemble the pieces of glass in the
correct order; the inside glass has a special heat-reflecting finish!