Interface, B.3.3 interface – Comtech EF Data C5 User Manual
Page 293
C5/K1/K3 Integrated Satellite Terminal System
Remote Control Operation
Rev. 0
B–9
B.3.3 Interface
Interface
Transmit
Overhead Type
Command:
Response:
Status:
Response:
<add/ITOT_xxxxx'cr'
>add/ITOT_xxxxx'cr''lf']
<add/ITOT_'cr'
>add/ITOT_xxxxx'cr''lf']
Where: xxxxx = NONE, EFD, or ASYNC.
Interface
Receive
Overhead Type
Command:
Response:
Status:
Response:
<add/IROT_xxxxx'cr'
>add/IROT_xxxxx'cr''lf']
<add/IROT_'cr'
>add/IROT_xxxxx'cr''lf']
Where: xxxxx = NONE, EFD, or ASYNC.
TX Driver Type
Command:
Response:
Status:
Response:
<add/TXDR_xxxxx'cr'
>add/TXDR_xxxxx'cr''lf']
<add/TXDR_'cr'
>add/TXDR_xxxxx'cr''lf']
Where: xxxxx = G703, V35, RS422, or RS232.
RX Driver Type
Command:
Response:
Status:
Response:
<add/RXDR_xxxxx'cr'
>add/RXDR_xxxxx'cr''lf']
<add/RXDR_'cr'
>add/RXDR_xxxxx'cr''lf']
Where: xxxxx = G703, V35, RS422, or RS232.
Transmit Clock
Command:
Response:
Status:
Response:
<add/TC_xxx'cr'
>add/TC_xxx'cr''lf']
<add/TC_'cr'
>add/TC_xxx'cr''lf']
Where: xxx = INT (internal SCT clock), EXT
(external TX terrestrial clock), REF (external clock-
reference frequency).
External Clock-
Reference
Frequency
Command:
Response:
Status:
Response:
<add/ERF_nnnnn.n'cr'
>add/ERF_nnnnn.n'cr''lf']
<add/ERF_'cr'
>add/ERF_nnnnn.n'cr''lf']
Where: nnnnn.n = 8.0 to 10000.0 (external clock
frequency in kHz).
Transmit Clock
Phase
Command:
Response:
Status:
Response:
<add/TCP_xxxx'cr'
>add/TCP_xxxx'cr''lf']
<add/TCP_'cr'
>add/TCP_xxxx'cr''lf']
Where: xxxx = NRM (normal clock phasing), INV
(inverted clock phasing), AUTO (automatic clock
phasing).
Buffer Clock
Command:
Response:
Status:
Response:
<add/BC_xxx'cr'
>add/BC_xxx'cr''lf']
<add/BC_'cr'
>add/BC_xxx'cr''lf']
Where: xxx = INT (internal SCT clock), EXT
(external TX terrestrial clock), SAT (receive satellite
clock), REF (external clock-reference frequency),
Receive Clock
Phase
Command:
Response:
Status:
Response:
<add/RCP_xxx'cr'
>add/RCP_xxx'cr''lf']
<add/RCP_'cr'
>add/RCP_xxx'cr''lf']
Where: xxx = NRM (normal clock phasing), INV
(inverted clock phasing).
Base Band Loop
Back
Command:
Response:
Status:
Response:
<add/BBL_xxx'cr'
>add/BBL_xxx'cr''lf']
<add/BBL_'cr'
>add/BBL_xxx'cr''lf']
Where: xxx = ON or OFF.