Comtech EF Data SNM-1001 - Manual (Page 69)

Remote Control Operation SNM-1001 Network Control Modem
A–10 Rev. 1
Interface
ADPCM
Program Command:
Response:
Status:
Response:
<add/ADP_xxx'cr'
>add/ADP_xxx'cr''lf']
<add/ADP_'cr'
>add/ADP_xxx'cr''lf']
Where: xxx = ON or OFF.
Note: Only valid when ADPCM board is installed.
Interface
Subscriber/
Trunk
Emulation Command:
Response:
Status:
Response:
<add/SBTR_xxx'cr'
>add/SBTR_xxx'cr''lf']
<add/SBTR_'cr'
>add/SBTR_xxx'cr''lf']
Where: xxx = SUB or TRK.
Note: Only valid when ADPCM board is installed.
E & M
Signal Type Command:
Response:
Status:
Response:
<add/EMS_n'cr'
>add/EMS_n'cr''lf']
<add/EMS_'cr'
>add/EMS_n'cr''lf']
Where: n = 1 to 5, in steps of 1.
Note: Only valid when ADPCM board is installed.
Interface
Encoding
Law Command:
Response:
Status:
Response:
<add/LAW_y'cr'
>add/LAW_y'cr''lf']
<add/LAW_'cr
>add/LAW_y'cr''lf']
Where: y = A (A-Law) or U (u-Law).
Off Hook
Alert Enable Command:
Response:
Status:
Response:
<add/HOOK_xxx'cr'
>add/HOOK_xxx'cr''lf']
<add/HOOK_'cr
>add/HOOK_xxx'cr''lf']
Where: xxx = ON or OFF.
Note: Only valid when ADPCM board is installed.
Interface
Service
Channel
Level Command:
Response:
Status:
Response:
<add/ISCL_xx_nnn'cr'
>add/ISCL_xx_nnn'cr''lf']
<add/ISCL_xx'cr'
>add/ISCL_xx_nnn'cr''lf']
Where:
xx = TX or RX (service channel designator).
nnn = -20 to +10, in steps of 1 (service channel level in
dBm).
Note: Only valid when ADPCM board is installed.
Interface
RD Signal Command:
Response:
Status:
Response:
<add/RD_xxx'cr'
>add/RD_xxx'cr''lf']
<add/RD_'cr'
>add/RD_xxx'cr''lf']
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Interface
SD Signal Command:
Response:
Status:
Response:
<add/SD_xxx'cr'
>add/SD_xxx'cr''lf']
<add/SD_'cr'
>add/SD_xxx'cr''lf']
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Interface
RR Signal Command:
Response:
Status:
Response:
<add/RR_xxx'cr'
>add/RR_xxx'cr''lf']
<add/RR_'cr'
>add/RR_xxx'cr''lf']
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Interface
DM Signal Command:
Response:
Status:
Response:
<add/DM_xxx'cr'
>add/DM_xxx'cr''lf']
<add/DM_'cr'
>add/DM_xxx'cr''lf']
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Interface
ASYNC
Communi-
cations
Program Command:
Response:
Status:
Response:
<add/ACP_xxx'cr'
>add/ACP_xxx'cr''lf']
<add/ACP_'cr'
>add/ACP_xxx'cr''lf']
Where: xxx = ON or OFF.
Note: Only valid when ASYNC board is installed.