Comtech EF Data SNM-1001 User Manual
Page 85
Remote Control Operation
SNM-1001 Network Control Modem
A–26
Rev. 1
Bulk Consol
Status
(Continued)
Parameter
Number
Parameter Name
(Command Reference)
Description
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
(Note 1)
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Buffer clock source
(ref. "BC_" command).
Receive clock phase
(ref. "RCP_" command).
Baseband loopback
(ref. "BBL_" command).
Interface Buffer Programming
(ref. "IBP_" command).
Interface buffer size
(ref. "IBS_" command).
Modem operation mode
(ref. "MOM_" command).
MODEM REMOTE/LOCAL mode.
ADPCM Interface Programming
(ref. "APD_" command)
ADPCM Subscriber/Trunk
Emulation
(ref. "SBTR_" command).
ADPCM E & M Signal Type
(ref. "EMS_" command).
ADPCM Encoding Law
(ref. "LAW_" command).
Off hook alert enable
(ref. "HOOK_" command).
ADPCM Transmit Service Channel
Level (ref. "ISCL_" command).
ADPCM Receive Service Channel
Level (ref. "ISCL_" command).
ADPCM RS-422 Send Data Signal
Programming (ref. "SD_" command).
ADPCM RS-422 Receive Signal
Programming (ref. "RD_" command).
ADPCM RS-422 Receiver Ready
Signal Programming (ref. "RR_"
command).
ADPCM RS-422 Data Mode Signal
Programming (ref. "DM_" command).
p36 = n, where 'n' is '0' (INT), '1' (REF), '2' (EXT), or '3'
(SAT).
p37 = n, where 'n' is '0' (NRM) or '1' (INV).
p38 = n, where 'n' is '0' (off) or '1' (on).
p39 = n, where 'n' is '0' (BITS ) or '1' (MS).
p40 = nnnnnn, buffer size in bits or milli seconds.
p41 = n, where 'n' is '1' (TX_ONLY), '2' (RX_ONLY), or '3'
(DUPLEX).
p42 = n, where 'n' is '0' (LOCAL) or '1' (REMOTE).
p43 = n, where 'n' is '0' (off) or '1' (on).
p44 = n, where 'n' is '0' (Subscriber) or '1' (Trunk).
p45 = n, where 'n' is '1', '2', '3', '4', or '5' (signal type).
p46 = n where 'n' is 'A' (A-Law ) or 'U' (u-Law)
p47 = n, where 'n' is '0' (off) or '1' (on).
p48 = nnn, service channel level in dBm.
p49 = nnn, service channel level in dBm.
p50 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).
p51 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).
p52 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).
p53 = n, where 'n' is '0' (NORMAL) or '1' (INVERT).