Comtech EF Data SNM-1001L - Manual (Page 287)

SNM-1001L Satellite Modem Revision 1
Remote Control Operation MN/SNM1001L.IOM
B–13
AUPC
Maximum
Power Limit Command:
Response:
Status:
Response: <add/MAXP_snn.n'cr'
>add/MAXP_snn.n'cr''lf']
<add/MAXP_'cr'
>add/MAXP_snn.n'cr''lf']
Where: snn.n = -30.0 to -5.0, in 0.1 steps (nominal range
in dBm).
Notes:
1. The nominal power range is modified relative to
the value specified by the modulator power offset
(MPO_).
2. ASYNC or AUPC Overhead only.
AUPC
Minimum
Power Limit Command:
Response:
Status:
Response: <add/MINP_snn.n'cr'
>add/MINP_snn.n'cr''lf']
<add/MINP_'cr'
>add/MINP_snn.n'cr''lf']
Where: snn.n = -30.0 to -5.0, in 0.1 steps (nominal range
in dBm).
Notes:
1. The nominal power range is modified relative to
the value specified by the modulator power offset
(MPO_).
2. ASYNC or AUPC Overhead only.
AUPC
Eb/N0
Target Set
Point Command:
Response:
Status:
Response: <add/ENSP_nn.n'cr'
>add/ENSP_nn.n'cr''lf']
<add/ENSP_'cr'
>add/ENSP_nn.n'cr''lf']
Where: nn.n = 3.2 to 16.0, in 0.1 increments (Eb/N0 in
dB).
Note: AUPC Overhead only.
AUPC
Maximum
Tracking
Rate Command:
Response:
Status:
Response: <add/MAXT_n.n'cr'
>add/MAXT_n.n'cr''lf']
<add/MAXT_'cr'
>add/MAXT_n.n'cr''lf'] Where: n.n = 0.5 to 6.0, in 0.5 increments (max tracking
rate in dBm/minute).
Note: AUPC Overhead only.
AUPC Local
Carrier Loss
Action Command:
Response:
Status:
Response: <add/LCL_xxxx'cr'
>add/LCL_xxxx'cr''lf']
<add/LCL_'cr'
>add/LCL_xxxx'cr''lf'] Where: xxxx = HOLD, NOM, or MAX (power level setting
when local carrier loss).
Note: AUPC Overhead only.
AUPC
Remote
Carrier Loss
Action Command:
Response:
Status:
Response: <add/RCL_xxxx'cr'
>add/RCL_xxxx'cr''lf']
<add/RCL_'cr'
>add/RCL_xxxx'cr''lf'] Where: xxxx = HOLD, NOM, or MAX (power level setting
when remote carrier loss).
Note: AUPC Overhead only.
Remote
Modem
AUPC
Commands
Notes:
1. Always wait 3 seconds between consecutive remote modem command/status polls.
2. If Local AUPC is not enabled, status commands will return last known condition. They will also request status
from the remote modem. This allows a second request to return proper status.
Remote
AUPC
Enable Command:
Response:
<add/RPC_xxx'cr'
>add/RPC_xxx'cr''lf' Where: xxx = ON or OFF (remote AUPC enable).
Note: AUPC Overhead only.
Remote
Interface
Substitution
Pattern Command:
Response:
Status:
Response: <add/RISP_xxx'cr'
>add/RISP_xxx'cr''lf']
<add/RISP_'cr'
>add/RISP_xxx'cr''lf']
Where: xxx = ON or OFF (remote transmit 2047 pattern
enable).
Notes:
1. Transmit 2047 Pattern.
2. AUPC Overhead only.
Remote
Interface
Baseband
Loopback Command:
Response:
Status:
Response: <add/RBBL_xxx'cr'
>add/RBBL_xxx'cr''lf']
<add/RBBL_'cr'
>add/RBBL_xxx'cr''lf'] Where: xxx = ON or OFF (remote baseband loopback
enable).
Note: ASYNC or AUPC Overhead only.