Flowserve TB-MAG INNOMAG - Manual (Page 26)

INNOMAG® TB- MAG™ ASME and ISO SEALLESS ENGLISH 26999988 06-14
Page 26 of 44
6.3.2 Storage of spares
Spares should be stored in a clean dry area away
from vibration. Inspection and re-treatment of
metallic surfaces (if necessary) with preservative is
recommended at 6 monthly intervals.
6.3.3 Recommended spares
For two years operation (as per VDMA 24296).
FIN
no.
Designation
Number of same size pumps
(including stand-by)
2 3 4 5 6/7 8/9 10(+)
2200
Impeller
Assembly
1 2 20%
3500
Containment
Shell Assembly
1 2 20%
3041.2,
1500.1,
6810.1
Suction Ring Kit 1 2 20%
4610 Gasket / O-ring 1 2 3 30%
0230
Outer Magnet
Assembly
- - - 1 2
- Power end - - - - - 1 2
6.4 Tools required
A typical range of tools that will be required to
maintain these pumps is listed below.
6.4.1 Readily available in standard tool kits,
and dependent on pump size:

9/16, 1/2, 5/8, 3/4, 15/16 in. Wrench & Socket

17, 19, 24 mm Spanner & Socket

Allen keys, up to 10 mm across flats

3/16 in. & 1/4 in. T-Handle Allen Wrench

Wire Cutter

Soldering Iron

Range of screwdrivers

Soft mallet

Jackscrew Bolts
o A Series containment ring [3830]: (2) 1/2
in. -13 x 5 in.
o E Series containment ring [3830]: (2) M12 -
1.75 x 11 cm
o B/C Series containment ring [3830]: (2) 5/8
in.-11 x 5 in.
o F/G Series containment ring [3830]: (2)
M16 - 2 x 11 cm
o A/E Series ASME Adapter [1340]: (2) 1/2
in. -13 x 5 in.
o A/E Series IEC Adapter [1340]: (2) M12 -
1.75 x 11 cm
o B/C/F/G Series ASME Adapter [1340]: (2)
5/8 in.-11 x 5 in.
o B/C/F/G Series IEC Adapter [1340]: (2)
M16 - 2 x 11 cm
o ASME Outer Magnet [0230]: 1/2 in. - 13 x
4.5 in.
o IEC Outer Magnet [0230]: (2) M8 -1.25 x
30 mm, M12 - 1.75 x 100+mm jackscrew
and jackscrew plate (TLG-2042-SI)

Needle Nose Pliers

Arbor Press

Lathe

Caliper

Hobby Knife
6.4.2 Flowserve Innomag® Specialized
Equipment:

Shaft Removal Tool
a) A/E Series Part # TLG-2017-AA
b) B/C/F/G Series Part # TLG -2018-AA

Shaft Centering Tool
a) A/E Series Part # TLG-2013-SI
b) B/C/F/G Series Part # TLG-2015-SI
c)
C Series (‘H’ Models) Part # TLG-2014-SI

Bushing Installation / Removal Kit
a) Part # TLG-2016-AA

Dial test indicator

Impeller Trimming Sleeve
a) A/E Series Part # TLG-2033-AA
b) B/C/F/G Series Part # TLG-2023-AA
6.5 Fastener torques
Fastener Screw size Torque Nm (lbf •ft)
All except
where
otherwise
stated
M8 (5/16in.)
M10 (3/8in.)
M12 (1/2in.)
M16 (5/8in.)
M20 (3/4in.) 16 (12)
25 (18)
35 (26)
80 (59)
130 (96)
Non-metallic gaskets incur creep
relaxation - before commissioning the pump check
and retighten fasteners to tightening torques stated.
6.6 Disassembly
The preventative maintenance and disassembly
procedures are intended for use during standard
field inspection or service. The disassembly can
take place while the pump is piped up or in a
maintenance shop. If at all possible, it is
recommended to perform all repairs using the shop
procedures to reduce the risk of damage to SiC
parts.
Lock out driver power to prevent accidental
start-up that could result in serious personal injury.
Lock out and/or disconnect power.
Shut off all valves controlling flow
to and from the pump. Isolate the pump from the
system and relive any remaining system pressure.