Osburn AC02585 - Manual (Page 6)

6
Splitz-it 5-tON electric lOg Spliter Splitz-it 5-tON electric lOg Spliter
oil drain plug
dipstick
bleed screw
Figure 2
PARTS TO BE FREE OF
BURRS AND SHARP EDGES
THIS DRAWING AND ALL INFORMATION CONTAINED HEREIN IS AND REMAINS THE PROPERTY OF ARDISAM INC.
AND IS CONFIDENTIAL. IT IS SUBMITTED AND MAY BE USED ONLY IN CONNECTION WITH ARDISAMS' PROPOSALS
AND/OR ITS CUSTOMERS' ORDERS. IT SHALL NOT BE DISCLOSED TO OTHERS OR COPIED WITHOUT ARDISAMS'
SPECIFIC WRITTEN CONSENT AND SHALL BE IMMEDIATELY RETURNED UPON REQUEST.
MATERIAL TOLERANCE UNLESS
OTHERWISE NOTED:
0.0 ±.100 INCH ± 2.54 MM
0.00 ±.030 INCH ± 0.76 MM
0.000 ±.010 INCH ± 0.25 MM
ANGLES:
0 ± 2°
0.0 ± 1.0°
THREADS CLASS 2
PRIMARY DIMENSIONS ARE IN INCHES
SECONDARY DIMEMSION ARE IN MM
ALL ANGLES ARE DECIMAL DEGREES
UNLESS OTHERWISE SPECIFIED
NAME
TREATMENT
DR BY APPD PRT NO W1200
PT WEIGHT SURFACE AREA DATE REVISION
THIRD ANGLE PROJECTION
SEE BILL OF MATERIALS
NONE
32121.68 3451644.89
W1200 5 TON ELECTRIC
LOG SPLITTER
1
MATT OLSEN MDO 9/17/2010
09/17/2010 SHEET: 6 OF 8
SET-Up AND pRE-OpERATiON
Before attempting to use, familiarize yourself with all the
operating features and safety requirements of your log splitter.
(SEE FigURE 1)
1. Wedge 8. 2-hand operating
2. Oil tank hydraulic control lever
3. Carrying handle 9. Safety guard for 2-hand
4. Supporting leg operating hydraulic
5. Motor w/push switch control lever
& circuit breaker 10. Log pusher
6. Rubber feet 11. Log cradle
7. Rolling wheel
ASSEMbLY
1. Attach the control lever assembly by screwing the knob to the end of the lever. (SEE FigURE 3)
2. Bolt the rolling wheel bracket to the log splitter beam and log cradles using the four M6-1 x 12 bolts and corresponding lock
and flat washers provided. (SEE FigURE 3)
3. Attach safety guard lever to the top of the rolling wheel bracket with M6-1 x 12 bolts provided. (SEE FigURE 3)
4. Assemble the handle bars to the handle, then attache the completed handle bar assembly to the log splitter beam using the
M6 x 12 bolts, the M6 x 1.5 washer, and the M6 x 13 x 1.75 washers provided. (SEE FigURE 4)
Figure 3
Figure 4
wARNiNg
FOR YOUR OwN SAFETY, DO NOT cONNEcT THE LOg
SpLiTTER TO THE pOwER SOURcE UNTiL THE MAcHiNE
iS cOMpLETELY ASSEMbLED AND YOU READ AND
UNDERSTAND THE ENTiRE iNSTRUcTiON MANUAL.
FOR YOUR OwN SAFETY, NEVER FORgET TO bOLT THE
wHEEL bRAckET TO THE LOg SpLiTTER, LiFT THE LOg
SpLiTTER bY THE HANDLES AT bOTH ENDS AND pLAcE
iT ON A 60-75cM HigH, STAbLE, FLAT AND LEVEL wORk
SURFAcE.
NEVER USE THE LOg SpLiTTER iF iT iS NOT iN pERFEcT
ORDER OR iF iT NEEDS SERViciNg. bEFORE STARTiNg
wORk, cHEck cORREcT FUNcTiONiNg OF ALL THE
cONTROLS (HYDRAULic LEVER, pUSH bUTTON).
iMpORTANT
bEFORE OpERATiNg THE LOg SpLiTTER, THE bLEED
ScREw SHOULD bE LOOSENED bY 3-4 ROTATiONS SO
AiR cAN gO iN AND OUT OF THE OiL TANk SMOOTH-
LY. AiR FLOw THRU THE bLEED ScREw HOLE SHOULD
bE DETEcTAbLE DURiNg LOg SpLiTTER OpERATiON.
bEFORE MOViNg THE LOg SpLiTTER, MAkE SURE
THE bLEED ScREw iS TigHTENED TO AVOiD OiL
LEAkAgE FROM THiS pOiNT. (See Figure 2)
cAUTiON
FAiLURE TO LOOSEN THE bLEED ScREw wiLL RESULT iN
AiR bEiNg cOMpRESSED AND DEcOMpRESSED iN THE
HYDRAULic SYSTEM. cONTiNUOUS AiR cOMpRESSiON
AND DEcOMpRESSiON wiLL bLOw OUT THE SEALS OF
THE HYDRAULic SYSTEM AND cAUSE pERMANENT
DAMAgE TO THE LOg SpLiTTER.
cAUTiON
DO NOT ADJUST THE MAxiMUM pRESSURE LiMiTiNg
ScREw. THE pRESSURE LiMiTiNg ScREw HAS bEEN
SEALED AT THE FAcTORY TO pREVENT UNAUTHORiZED
ADJUSTiNg. RESETTiNg THE ScREw wiLL cAUSE
THE HYDRAULic pUMp TO FAiL TO OUTpUT ENOUgH
SpLiTTiNg pRESSURE OR cAUSE TOO MUcH pRESSURE,
wHicH MAY RESULT iN SERiOUS iNJURY, AS wELL AS
DAMAgE TO THE MAcHiNE.
1
3
2
4
7
5 6
10
9
11
8
Figure 1
SBIOMWENGSplitzIt.indd 6 1/10/2012 8:14:43 AM