Miomare LED Washbasin Fitting / LED Bath/Shower Fitting - Manual (Page 32)

32 GB
Installation / Operation
designated female threads on the fitting 1
(see Fig. C2).
Unscrew the handle from part 1 of the pop-up
pull rod 3 and insert it into the fitting 1 from
the bottom up so the female thread on the han-
dle faces to the back through the rear opening
on the fitting. Then screw it to the handle (see
Fig. C3).
Position the fitting 1 over the washbasin tap
hole (see Fig. C4).
Below the washbasin first place the C sealing
washer 6 , then the C metal washer 7 over
the two thread bolts 8 (see Fig. C4).
Now screw the securing nuts 9 onto the thread
bolts 8 and tighten with a spanner SW 9 mm
until the fitting 1 is firmly seated on the
washbasin (see Fig. C4).
Unscrew the upper pop-up flange 15 from the
lower pop-up flange 17 .
From the top insert the upper pop-up flange 15
with the upper pop-up seal 14 into the wash-
basin drain hole.
Place the lower pop-up flange 17 with the lower
pop-up seal 16 beneath the washbasin drain
hole.
Now screw together the lower pop-up flange
17 and the upper pop-up flange 15 so the
pop-up plastic nut 19 faces to the back (see
Fig. C5).
Unscrew the pop-up plastic nut 19 from the
lower pop-up flange 17 , leaving the seal in-
side the female thread of the lower pop-up
flange
17 .
ATTENTION! DANGER OF INJURY, SHEET
METAL HAS SHARP EDGES.
Temporarily remove the clip and pop-up joint 11
from the pop-up pivot rod 12 for installation.
Be sure the seal remains on the pop-up pivot
rod
12 .
Place the pop-up plastic nut 19 over the longer
piece of the pop-up pivot rod 12 . Be sure the
seal is placed between the ball and pop-up
plastic nut
19 .
Inset the short section of the pop-up pivot rod
12 into the female thread of the lower pop-up
flange 17 and retighten the pop-up plastic nut
19 hand tight.
Reattach the clip and pop-up joint 11 to the
pop-up pivot rod 12 .
Insert the pup-up pull rod 5 through the plas-
tic section of the pop-up joint 11 and tighten
the screw using a cross-tip screwdriver.
Verify the pop-up is working properly. The plas-
tic screw below the pop-up drain plug 13 may
need to be adjusted. Then retighten with the
lock nut.
Install the siphon by screwing together the
siphon and the pop-up screw thread 18 .
Check the seals inside the swivel nuts 20 on
the flexible connection hoses 10 .
Screw the flexible connection hoses 10 to the
angle valves. Be sure to correctly install the
flexible connection hoses
10 to the cold- / hot
water hoses – left flexible connection hose 10
to the hot water connection, left angle valve,
and the right flexible connection hose
10 to
the cold water connection, right angle valve
(refer to Fig.C5).
Operation
Start-up
After the initial commissioning, carefully check all
connections for leaks.
Check the operation of the fitting. To do so,
swing the handle 23 into all permissible posi-
tions.
Note: the fitting 1 features an LED light. The LED
is lit through an integrated turbine (without batteries).
The LED colour changes automatically based on the
water temperature through an integrated tempera-
ture sensor:
· up to approx. 33°C blue,
· from approx. 33-43°C green,
· over approx. 43°C red.
Note: over approx. 53°C the LED light will begin
to flash red to warn of potential scalding.