Fig.1 fig.3 fig.2, Specifications 3. assembly and installation – Sealey SAC82425VLN User Manual
Page 2
3.1 AssembLY
3.1.1 remove compressor from packaging and inspect for any shortages or
damage. if anything is found to be missing or damaged, contact
your supplier.
3.1.2 save the packing material for future transportation of the compressor.
We recommend that the packing is stored in a safe location, at
least for the period of the guarantee. then, if necessary, it will be
easier to send the compressor to the service centre.
3.1.3 confirm that the mains voltage corresponds with the voltage shown
on the compressor data plate.
3.1.4
sAc89025vLN oNLY - fit the main wheels (fig.1.A) and two smaller
wheels (fig.1.B) to the main frame using the nuts, bolts and
washers supplied.
3.2 iNsTALLATioN
3.2.1 the compressor should be installed on a flat, firm surface, or one that
does not exceed 10° either transversely or longitudinally, and should
be in a position that allows good air circulation around the unit.
3.2.2 the compressor is shipped with oil in the pump, but the level needs
checking before starting the unit for the first time. check the oil level by
referring to the oil dipstick (fig.2, fig.3) to check the oil. if the oil level
is not between minimum and maximum on the dipstick it should be
topped up. remove the dipstick and if required, pour in the
recommended oil. on model sAc82425VLn one of the side panels
will need to be removed to get to the motor (fig.3).
3.2.3 the compressor must be positioned so that the panels may be
removed and compressor components easily accessed for
maintenance. the location must have good air exchange and an
adequate air flow around the unit as the compressor generates
significant heat. in contaminated areas an extraction system
must be installed to remove dust, vapours and gases.
Do NoT install
the compressor in very high dust locations.
2. speciFicATioNs
3. AssembLY AND iNsTALLATioN
All performance figures are ± 5%
* Note: 2.5 bar is recommended pressure setting for spraying.
6.0 bar is recommended pressure setting for air tools.
fig.1
fig.3
fig.2
7
Do NoT attempt to move the compressor by pulling the air tool hose.
7
Do NoT use this product to perform a task for which it has not been designed.
7
Do NoT operate the compressor with any of the panels removed.
7
Do NoT deface the certification plate attached to the end of the compressor tank.
7
Do NoT cover compressor or restrict air flow around the machine whilst operating.
DANGER! DO NOT direct the output jet of air towards people or animals.
7
Do NoT operate the compressor without an inlet air filter.
7
Do NoT allow anyone to operate the compressor unless they have received full instructions and adequate training.
wArNiNG! The air tank is a pressure vessel and the following safety measures apply:
7
DO NOT tamper with the safety valve and DO NOT modify or alter the tank in any way, DO NOT strap anything to the tank.
7
DO NOT subject the tank to impact, vibration or to heat and DO NOT allow contact with abrasives or corrosives.
3
Inspect inside walls for corrosion as per the maintenance section, have a detailed tank inspection carried out annually. Tank
shell must not fall below the certified thickness at any point.
wArNiNG! if an electrical fuse blows, ensure that it is replaced with one of identical type and rating.
3
when the compressor is not in use, it should be switched off, isolated from the mains supply and the air drained from the
tank.
3
When not in use, store the compressor carefully in a safe, dry, childproof location.
imporTANT wArNiNG - Air contaminants taken into the compressor will affect optimum performance.
example: Body filler dust or paint over-spray will clog the pump intake filter and may cause internal damage to pump/motor components.
Please note that any parts damaged by any type of contamination will not be covered by warranty.
model . . . . . . . . . . . . . . . . . . . . .sAc89025vLN. . . . sAc82425vLN
max motor output (hp/kw). . . . . . . . . . 2.5/1.8. . . . . . . . . . .2.5/1.8
voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230. . . . . . . . . . . . . 230
Air Displacment cfm (l/min). . . . . . . 10.3 (292). . . . . . . . 10.3 (292)
max Free Air Delivery cfm (l/min) . . . 7.5 (212). . . . . . . . . 7.5 (212)
Tank capacity (ltr) . . . . . . . . . . . . . . . . . . . . 90. . . . . . . . . . . . . . 24
model . . . . . . . . . . . . . . . . . . . . .sAc89025vLN. . . . sAc82425vLN
maximum pressure (psi/bar) . . . . . . . . 145/10. . . . . . . . . . .145/10
Noise db(a) . . . . . . . . . . . . . . . . . . . . . . . . . . 66. . . . . . . . . . . . . . 57
Noise Lw(a) . . . . . . . . . . . . . . . . . . . . . . . . . . 90. . . . . . . . . . . . . . 80
weight kg . . . . . . . . . . . . . . . . . . . . . . . . . . . 83. . . . . . . . . . . . . . 96
Dimensions (wxDxH) mm . . . 1030x520x1020. . . . . 490x700x930
Original Language Version
sAc89025VLn, sAc82425VLn issue: 2 - 22/02/12