Fulton Performance XPD15L0301 User Manual
Page 2
Use only Cequent Performance Products parts or parts of equal quality for repair. Replacement parts are available through Cequent Performance
Products Customer Service Department, 1-800-521-0510. Please specify product model number.
Maintenance
Installation
Instructions
(Continued)
How to Order
Limited Warranty
The following procedures should be performed at least annually: For side-wind models, the internal gearing and bushings of the jack must be kept
lubricated. Apply a small amount of automotive grease to the internal gearing by removing the jack cover, or if equipped, use a needle nose applicator or
standard grease gun on the lubrication point found on the side of the jack near the crank. Rotate the jack handle to distribute the grease evenly. A
lightweight oil must be applied to the handle unit at both sides of the tube for side-wind models. If equipped, the axle bolt and nut assembly of the caster
wheel must also be lubricated with the same light weight oil. For top-wind models, apply a lightweight oil to the screw stem. If this product is used in a
marine environment, flush the jack assembly and bushings with fresh water, and apply fresh lubricant.
Oil
Grease
Oil
Grease
Oil
Oil
Spacer
Bolt
Nut
To attach a wheel assembly:
1) Insert the long spacer into the wheel.
2) Set the wheel into the caster body and place
the bolt through the caster body and wheel.
3) Secure with the nut provided.
Roller
Spacers
Bolt
Nut
To attach a handle assembly:
1) Insert the long spacer into the roller
followed by the thin spacer and the bolt.
2) Secure to the crank stem with the nut
provided.
Heavy Duty Caster:
1) Jack capacity limited to
lesser of jack or caster.
2) Use 4 3/8 bolts,
washers, and locknuts as
shown.
Weld-on Pivot Tube Mounting Instructions (Round and Square Pivot Tubes):
1) All welding must be performed by an AWS certified welder.
2) The non-beveled side of the pivot tube is welded to the tongue unless otherwise specified on hardware.
3) Place the weld-on pivot tube against the tongue and weld all around with a 3/16 fillet weld. Align
one set of pivot mount holes vertically.
4) Mate the jack to the pivot tube and secure with the supplied pin.
3/16
3/16
Pivot Pin
Pivot Tube
Beveled Side
Non-beveled Side
To attach a top-wind handle assembly:
1) Place the washer
over the screw
stem and then
place the handle
over the screw
stem.
2) Secure the handle
to the screw stem
with the bolt and
nut provided.
Handle
Bolt
Washer
Nut
Screw Stem
Oil
Grease
Limited Warranty. Cequent Trailer Products, Inc. ( We or Us ) warrants to the original consumer purchaser only ( You ) that the product
purchased will be free from material defects in both material and workmanship, normal wear and tear excepted, for a period of five years for
Bulldog® and Fulton® products and one year for the Pro-Series® products. The foregoing warranty is valid only if the installation and use
of the product is in accordance with product instructions. There are no other warranties, express or implied, including the warranty of
merchantability or fitness for a particular purpose. If the product does not comply with the applicable limited year warranty, Your sole and
exclusive remedy is that We will replace the product without charge to You and within a reasonable time or, at our option, refund the purchase
price. This limited warranty is not transferable.
Limitations on the Warranty. This limited warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect, misuse, or as a
result of any accident or in any other manner; (c) damage from misapplication, overloading, or improper installation, including welds; (d)
improper maintenance and repair; and (e) product alteration in any manner by anyone other than Us, with the sole exception of alterations made
pursuant to product instructions and in a workmanlike manner.
Obligations of Purchaser. You must retain Your product purchase receipt to verify date of purchase and that You are the original consumer
purchaser. To make a warranty claim, contact Us at 47774 Anchor Ct. W., Plymouth, MI 48170, 1-800-521-0510, identify the product by make
and model number, and follow the claim instructions that will be provided. The product and the purchase receipt must be provided to Us in order
to process Your warranty claim. Any returned product that is replaced or refunded by Us becomes our property. You will be responsible for
return shipping costs.
Remedy Limits. Repair or replacement is Your sole remedy under this limited warranty or any other warranty related to the product. We shall not be
liable for service or labor charges incurred in removing or replacing a product or any incidental or consequential damages of any kind.
Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the product
instructions is at Your own risk.
Governing Law. This limited warranty gives You specific legal rights, and You also may have other rights which vary from state to state. This
limited warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to conflicts of law. The state courts located
in Oakland County, Michigan shall have exclusive jurisdiction for any disputes relating to this warranty.
Removable Caster
Drop Foot
Plunger Pin
Outer Tube
Inner Tube
Drop Leg
Drop Leg Pin
Foot Plate
Plymouth, MI 48170 USA
800/521-0510