Mpman XRM34 - Manual (Page 4)

TO SET SLEEP FUNCTION(on the remote control)
1. If you want to fall asleep to music, press the SLEEP button .
2. You may select the TUNER, CD/MP3, USB, SD/MMC or AUX mode in sleep function to play from 90, 80, 70 up to
10 minutes of music before shutting itself off automatically.
NORMAL
FUNCTION SELECT
The function is that when it presses the button the mode is changed. Display changes as below:
AUX CD
TUNER
USB SD CARD
UK-3
EQ CONTROL(on the remote control)
EQ shows the present sound tone. When you press the EQ button , the sound tone changes as below:
ROCK CLASSIC POP PASS JAZZ
F1 F2
OPERATING THE UNIT
When you first plug the unit into the AC outlet,
You can press the STANDBY/ON button on the unit or on the remote control to switch the unit ON or
STANDBY. Turn off the main switch of the unit and pull the AC plug out of the wall socket if you want to switch off
completely.
POWER/STANDBY
Note: If the display shows "ERROR" while you set the “TIMER ON”, it means both “TIMER ON” and “TIMER OFF” is
the same. In this case, please go to “TIMER OFF” to set the off time first.
the unit will be in standby mode before turn ON the main switch on the
rear of the unit.
Note:
1. If there is no signal under the CD/USB DEVICES/ SD & MMC CARD mode, the main unit will be switched off
within 15 minutes automatically.
2. During in standby mode, press any button/key can make the display light for 10 seconds.
3. Please turn the main switch off to save energy, when you do not use the unit.
1. Press the STANDBY/ON button on the unit or on the remote control to switch the unit on.
2. Select the sound source (CD, USB, SD CARD, AUX or TUNER) by pressing the FUNCTION button. The
corresponding display will light up.
3. Adjust the volume with the VOLUME (+ or -) button on the unit or VOLUME (+ or -) button on the remote control.
4. Press the STANDBY/ON button again to turn off the unit.
CLOCK SETTING
During in the STANDBY mode.
1. Press and hold the MEM/C-ADJ. button until the time displays will change to 12-hour(or 24-hour) digit and flash.
2. Press the SKIP/TUNE SEARCH(UP or DOWN) button to adjust 12-hour or 24-hour digit.
3. Press the MEM/C-ADJ. button again, the HOUR digit will flash on the display, press the SKIP/TUNE SEARCH
(UP or DOWN) button to adjust HOUR digit.
4. Press the MEM/C-ADJ. button once more, the MINUTE digit will flash on the display, press the SKIP/TUNE
SEARCH (UP or DOWN) button to adjust MINUTE digit.
5. Press the MEM/C-ADJ. button again to confirm the time.
6. Each enable state as shown above will be cleared if the key is not pushed in10 seconds.
TIMER SETTING
During in the STANDBY OFF/ON mode.
1. After adjusting clock, press the TIMER button for a few seconds, " ON" and "00:00" appears on the display
and the HOUR digit flashes.(F1)
2. Press the SKIP/TUNE SEARCH(UP or DOWN) button to adjust it.
3. Press the TIMER button again, the MINUTE digit will start flashing, adjust it by pressing the SKIP/TUNE
SEARCH (UP or DOWN) button.
4. Press the TIMER button once more to confirm and order TIMER ON time.
5. After adjusting "TIMER ON", " OFF" appears on the display and the HOUR digit flashes.(F2)
6. Repeat the above steps 2 to 3, and then press the TIMER button once more to confirm and order TIMER OFF time.
7. Now the "TUNER" appears on the display with flashing, adjust “TUNER, CD, USB or SD CARD " by pressing
the SKIP/TUNE SEARCH(UP or DOWN) button.
8. Press the TIMER button again, the timer "VOL" indicator appears on the display and flashes, adjust the timer
volume high or low by pressing the TUNING/SKIP (UP or DOWN) button.
9. Each enable state as shown above will be cleared if the button is not pushed in 10 seconds.
10. After adjusting "TIMER ON" and "TIMER OFF" ,press the TIMER button, " " appears on the display.
11. The unit will be switched on automatically at "TIMER ON" order and start playing, the unit will be switched off
automatically at "TIMER OFF" order.
RADIO OPERATION
1. Press the FUNCTION button on the main unit (or remote control) to select the TUNER mode that to select the FM
operation.
2. Select the desired frequency with the SKIP/TUNE SEARCH(UP or DOWN) button on the main unit (or remote
control).