Sony Multi Interface Shoe Adapter - Manual (Page 18)

18
Important Notes on
Operation
Notes on using the transmitter
• The digital wireless microphone system product must be
used within a temperature range of 0 °C to 50 °C (32 °F
to 122 °F).
• Operating the transmitter near electrical equipment
(motors, transformers, or dimmers) may cause it to be
affected by electromagnetic induction. Keep the
transmitter as far from such equipment as possible.
• The presence of the lighting equipment may produce
electrical interference over the entire frequency range.
Position the transmitter so that interference is
minimized.
• To avoid degradation of the signal-to-noise ratio, do not
use the transmitter in noisy places or in locations subject
to vibration, such as the following:
- near electrical equipment, such as motors,
transformers or dimmers
- near air conditioning equipment or places subject to
direct air flow from an air conditioner
- near public address loudspeakers
- where adjacent equipment might knock against the
tuner
Keep the transmitter as far from such equipment as
possible or use buffering material.
On cleaning
• If the transmitter is used in a very humid or dusty place
or in a place subject to an active gas, clean its surface as
well as the connectors with a dry, soft cloth soon after
use. Lengthy use of the transmitter in such places or not
cleaning it after its use in such places may shorten its
life.
• Clean the surface and the connectors of the transmitter
with a dry, soft cloth. Never use thinner, benzene, alcohol
or any other chemicals, since these may mar the finish.
Notes on simultaneous multi-
channel operation
• Keep the microphone at least 30 cm (11 7 /
8
inches) away
from another transmitter/microphone.
When the distances between transmitters need to be
closer than the distances above, use a grouping system
for multi-channel systems that include both digital
wireless and analog wireless devices.
For details, refer to “Sony Digital Wireless Microphone
System Frequency Lists” on the supplied CD-ROM.
• When only digital wireless microphones are being used,
keep the transmitter at least 4 meters (13 feet) away from
the antenna of a receiver for up to 10 channels, and at
least 6 meters (20 feet) away for 11 or more channels.
• When a mixture of digital and analog wireless
microphones is being used, keep the transmitter at least
6 meters (20 feet) away from the antenna of a receiver.
• This system should be kept at least 100 meters (328 feet)
away from any analog wireless systems using the same
frequency when both are being used in a wide area with
no walls or obstructions.
• If you experience noise, increase the distance between
the transmitter and receiver or decrease the transmission
power on the transmitter.
Note on microphone and transmitter
combinations
It is recommended that you use the ECM-90BC, ECM-
90LM, ECM-77LM, ECM-77BC/9X, ECM-66BC/9X,
ECM-44BC/9X, or ECM-FT5BC. Sony lavelier
microphone with this transmitter. The transmission signal
may cause noise on some microphones. If you experience
noise, you may be able to reduce it by changing the
position of the microphone cable, moving the microphone
connection away from the antenna, or lowering the
transmission power.
CROSS REMOTE Compatibility
As the unit supports a wider band than previous
transmitters, establishing wireless remote communication
via CROSS REMOTE between the unit and DWX-series
devices requires firmware update for the receiver and
RMU-01 unit.
For details on updating the firmware on the DWX-series
receiver or RMU-01 unit, contact your Sony
representative.
For details on how to check the software version, refer to
the device’s operating instructions.
Applicable devices and versions
• DWR-R01D: Version: 1.28 or earlier
• DWR-S01D: Version: 1.16 or earlier
• DWR-R02D: Version: 1.09 or earlier
• DWR-S02D: Version: 1.07 or earlier
• DWR-R02DN: Version 1.18 or earlier
• DWR-S02DN: Version 1.18 or earlier
• RMU-01: Version 1.26 or earlier
To prevent electromagnetic interference from portable
communication devices
The use of portable telephones and other communication
devices near the DWT-B30 may result in malfunction and
interference with audio signals. It is recommended that
portable communication devices near the DWT-B30 be
turned off.