Bowers & Wilkins Pi7 S2 Noise-Canceling True Wireless In-Ear Headphones (Satin Black) - Manual (Page 5)

5
ENGLISH
6. Bluetooth Connectivity
6.1 Pairing
Your Pi7 S2 earbuds are designed to stream music
wirelessly from Bluetooth audio devices, such as
smartphones, tablets or computers. To do so, the
earbuds and source audio device must first be
paired.
When you receive your Pi7 S2 earbuds, they will be
ready to pair to any Bluetooth audio device.
6.1.1 Pairing iOS/Android Devices without
Google Fast Pair Service (GFPS), Mac or PC
1. The first time the charging case lid is opened,
the earbuds will automatically enter pairing
mode and the case indicator will flash blue.
To manually place the earbuds into pairing
mode, open the charging case lid and press
and hold the button inside the case for 1.5
seconds until the case indicator flashes blue.
See Diagram 5.
2. Go to the Bluetooth pairing menu of your
source device and select “Pi7 S2” from the
device list.
3. The case indicator will change to solid blue to
indicate pairing is successful.
Note: Your earbuds will automatically exit
Bluetooth pairing mode if no device is paired after
several minutes. If pairing fails, the indicator will
rapidly flash blue; please try pairing again.
Pi7 S2 can remember up to four paired Bluetooth
devices in total. Repeat the above steps to pair more
devices.
Note: On PC, the Pi7 S2 will appear as two
Bluetooth audio profiles: Stereo (default) and
Hands-Free (for telephony). The Hands-Free
profile will automatically be used when making
or receiving a call (e.g., Teams, Skype, Zoom,
etc.). However, the system volume will continue
controlling the previously selected device (Stereo
profile by default). To change the volume of the
earbuds while on a call, use the application
volume control or ensure the system volume
control is set to control the Hands-Free profile.
We recommend adding your earbuds to the
Bowers & Wilkins
Music app. This allows you
to configure your earbuds in detail and provides
helpful hints and tips to make the most of your new
earbuds. Please refer to section 7 for details on
installing and using your earbuds with the
Bowers & Wilkins
Music app.
6.1.2 Pairing Android 6.0+ Devices Supporting
Google Fast Pair Service (GFPS)
1. Place the case no further than 10 cm (4 inches)
away from the Android device and ensure the
Bluetooth connection is enabled.
2. The first time the charging case lid is opened,
the earbuds will automatically enter pairing
mode and the case indicator will flash blue.
To manually place the earbuds into pairing
mode, open the charging case lid and press
and hold the button inside the case for 1.5
seconds until the case indicator flashes blue.
See Diagram 5.
3. A GFPS (Google Fast Pair Service) notification
will pop up showing that your device has
been detected and request to start the pairing
process.
4. Press the Connect button to enable pairing;
successful connection will be shown in the
popup.
5. Once paired, the popup will direct you to the
Google Play store to install the
Bowers & Wilkins
Music app.
We recommend adding your earbuds to the
Bowers & Wilkins
Music app. This allows you
to configure your earbuds in detail and provides
helpful hints and tips to make the most of your new
earbuds. Please refer to section 7 for details on
installing and using your earbuds with the
Bowers & Wilkins
Music app.
6.2 Disconnecting from a Device
You can quickly disconnect Pi7 S2 from a device by
placing the earbuds back into the case. Alternatively,
you can manage connections in further detail using
the Bowers & Wilkins
Music app, in the Connections
page of the earbud Settings menu.
7. Bowers & Wilkins Music App
The Bowers & Wilkins Music app is available for free
on iOS and Android devices and provides extended
setup and adjustments to features such as Adaptive
Noise Cancellation, Ambient Pass-Through and
Wear Sensors. The app also provides additional
functions, such as Ambient Pass-Through level,
connection management and software updates.
To add your earbuds:
1. From your Android or iOS device, download
and install the Bowers & Wilkins Music app.
bowerswilkins.com/downloadapp
2. Ensure your earbuds are switched on by taking
them out of the charging case.
3. Launch the app, then read and follow the
instructions pertaining to notifications and
permissions.
4. The app should detect your earbuds
automatically and invite you to set up your
earbuds. Follow the in-app instructions to
complete the setup process.
5. If your earbuds are not detected automatically,
navigate to the Settings page ( icon), tap Add
product and follow the in-app instructions.
Diagram 5
Bluetooth pairing