Empire Comfort Systems SR-10T-3 - Manual (Page 16)

16941-5-0907 Page 16
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
1 13347 CASING SIDE ASSEMBLY - LEFT
2 SR-180 CASING BACK
3 R-2313 PIEZO IGNITOR
4 SR-008 CASING SIDE ASSEMBLY - RIGHT
5 SR-113 VALVE BRACKET
6 R-6563 GAS VALVE -SIT
7 12438 TUBING - GAS VALVE TO BURNER
8 12437 TUBING - INLET REGULATOR TO GAS
VALVE
9 10753 INLET REGULATOR BRACKET
10 R-5097 INLET REGULATOR - NAT
10 R-5098 INLET REGULATOR - LPG
11 SR-158 TUBING - GAS VALVE TO PILOT
12 R-2314 ORIFICE HOLDER
13 R-2317 MAIN BURNER ORIFICE - NAT
13 R-2476 MAIN BURNER ORIFICE - LPG
14 R-2331 BURNER
15 R-6308 PILOT ASSEMBLY (LPG ONLY)
(INCLUDES ITEMS 16 & 17)
INDEX PART
NUMBER NUMBER DESCRIPTION
SR-10T
INDEX PART
NUMBER NUMBER DESCRIPTION
15 R-6307 PILOT ASSEMBLY (NAT ONLY)
(INCLUDES ITEMS 16 & 17)
16 R-6310 PILOT THERMOCOUPLE
17 R-6309 SPARK IGNITOR
18 SR-179 PILOT BRACKET (NAT)
18 SR-032 PILOT BRACKET (LPG)
19 SR-153 ORIFICE SHIELD
20 R-2305 CHROME GRILL
21 SR-134 CASING LOUVER (2 REQUIRED)
22 SR-129 REFLECTOR ASSEMBLY
23 SR-135 HEAT SHIELD
24 R-1992 BULB CLIP
25 SR-154 OPTIONAL SRS-10 FLOOR STAND KIT
NS R-2390 IGNITOR WIRE
NS SR-216 HARDWARE PACKAGE
1. Spark electrode does not produce spark.
a. Spark electrode broken - replace.
b. Ignitor wire may not be attached to spark electrode -
attach.
c. Ignitor wire damaged - replace.
d. Piezo ignitor defective - replace.
2. Spark electrode produces spark but pilot does not light.
a. No gas to heater - turn on gas.
b. PILOT position not properly aligned - turn gas control knob
to PILOT position and depress.
c. Pilot is blocked from spider web or dirt - clean pilot, see
Page 14.
3. Pilot flame does not stay “ON” when control knob is
released.
a. Control knob in PILOT position not completely depressed
or held in long enough.
b. INTERLOCK latching device is operative - see “Lighting
Instructions,” Page 12, Step 9.
c. Thermocouple not tightened into gas control - tighten
thermocouple.
d. Pilot flame not surrounding thermocouple - clean pilot, see
Page 14.
e. Inlet gas pressure too low, contact gas supplier.
f. Thermocouple defective - replace.
g. Gas control defective - replace.
4. Main burner does not ignite.
a. Main burner orifice is blocked - clean, see “Main Burner Flame
Characteristics,” Page 13. Attention: The number stamped
on the main burner orifice is a millimeter diameter.
b. Inlet gas pressure too low, contact gas supplier.
5. Heater keeps shutting “OFF” during normal operation.
a. Pilot is blocked - clean pilot, see Page 14.
b. Inlet gas pressure too low, contact gas supplier
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through
the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your
equipment. Then determine the Part Number ( not the Index Number) and the Description of each part from the following appropriate
illustration and list. Be sure to give all this information.
Unvented Heater Model Number
Part Description
Unvented Heater Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529
TROUBLESHOOTING
HOW TO ORDER REPAIR PARTS
PARTS LIST