Epson LQ-570e - Manual (Page 4)

EPSON LQ-570e
4 - EPSON LQ-570e 4/00
Thickness 0.0025 to 0.0055 inch (0.065 to 0.14 mm)
Cut sheet feeder: 0.0028 to 0.0055 inch (0.07 to
0.14 mm)
Weight 14 to 24 lb (52 to 90 g/m 2 )
Cut sheet feeder: 18 to 24 lb (64 to 90 g/m 2 )
Single-sheet multipart forms:
front entry only
Width 3.9 to 10.1 inches (100 to 257 mm)
Length 3.9 to 14.3 inches (100 to 364 mm)
Copies 1 original
+
up to 4 copies
Thickness 0.0047 to 0.015 inch (0.12 to 0.39 mm)
Weight 12 to 15 lb (40 to 58 g/m 2 )
Binding Line glue at the top of form
Envelopes: top entry only
Size No. 6 6.5
×
3.6 inches (165
×
92 mm)
No. 10 9.5
×
4.1 inches (241
×
105 mm)
Thickness 0.0063 to 0.0205 inch (0.16 to 0.52 mm)
Weight 12 to 24 lb (45 to 90 g/m 2 )
Postcards: front and top entry
Width Front and top: 3.9 to 7.9 inches (100 to 200 mm)
Cut sheet feeder: 3.9 to 5.8 inches (100 to 148 mm)
Length Front: 5.8 to 7.9 inches (148 to 200 mm)
Top: 3.9 to 7.9 inches (100 to 200 mm)
Cut sheet feeder: 3.9 to 5.8 inches (100 to 148 mm)
Thickness 0.0087 inch (0.22 mm)
Weight 51 lb (192 g/m 2 )
Continuous paper (standard and multipart):
front, rear, and bottom entry
Width 4 to 10 inches (101.6 to 254 mm)
Length 4 to 22 inches (101.6 to 558.8 mm)
Copies 1 original
+
up to 4 copies
Thickness Printable area
0.0025 to 0.015 inch (0.065 to 0.39 mm)
Perforated edges
up to 0.035 inch (0.9 mm)
Weight (not multipart) 14 to 22 lb (52 to 82 g/m 2 )
Weight (1 multipart sheet) 12 to 15 lb (40 to 58 g/m 2 )
Binding Point glue or paper staples on both sides
(front, bottom, or rear entry)
❏ The continuous multipart forms should be securely joined
together along the left and right edges by crimping.
Crimping should be pressed in from the original sheet side
and go completely through all copy sheets.
❏ The ratio of the cut/uncut length at the perforation should
be between 3:1 and 5:1.
❏ The perforation between pages should not extend all the
way to the edges of the paper.
❏ At the perforation between pages, the horizontal and
vertical perforation cuts should not cross.
❏ The thickness of the perforation part when extended should
be 1 mm or less.
Continuous paper with labels:
front and bottom entry
Label size (minimum) 0.938
×
2.5 inches (23.8
×
63.5 mm)
0.1 inch (2.5 mm) corner radius
Backing sheet width 4 to 10 inches (101.6 to 254 mm)
Backing sheet length 4 to 22 inches (101.6 to 558.8 mm)
Backing sheet thickness 0.0028 to 0.0035 inch
(0.07 to 0.09 mm)
Total thickness 0.0063 to 0.0075 inch
(0.16 to 0.19 mm)
Label weight 17 lb (64 g/m 2 )
Roll paper:
rear entry with optional roll paper holder only
Width 8.5
±
0.12 inch (216
±
3 mm)
Thickness 0.0028 to 0.0035 inch (0.07 to 0.09 mm)
Weight 14 to 22 lb (52 to 82 g/m 2 )
Paper Alignment
Front entry
Printing starts at “0” on the scale. The unprintable area is to the
left of the “0”.