Elektra Beckum TKHS 315 P - Manual (Page 12)

24
ENGLISH
9.4 Maintenance
Before switching ON
Visual check if distance saw blade – riv-
ing knife is 3...8 mm.
Visual check of power cable and power
cable plug for damage; if necessary
have damaged parts replaced by a qual-
ified electrician.
After switching OFF
Check to see if the saw blade post-runs
for more than 10 seconds; if so, have the
electronic motorbrake replaced by a
qualified electrician.
Monthly (if used daily)
Remove saw dust and chips with vac-
uum or brush; apply light coat of oil to
guide elements:
−
threaded rod and guide rods of
blade rise and fall mechanismn:
−
swivel segments.
Every 300 hours of operation
Check all screwed joints, retighten if
necessary.
A
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
•
Lower saw blade fully.
•
Dismount add-on parts (fence, slid-
ing carriage, table extension).
•
If possible use original carton for
shipping.
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A Universal Wheel Set
For easy moving.
B Sliding Carriage
For convenient guiding of long
stock.
C Table Side Extension, right
Table size 1000 mm x 600 mm;
with foldable supports.
D Suction Adapter to connect a shop
vacuum to the dust collection
attachment.
E Care and Maintenance Spray to
remove resin residue and preserve
metal surfaces.
F Saw blade CV 315 x 1.8 x 30
56 multiple combination teeth
for solid wood and particle board.
G Saw blade CV 315 x 1.8 x 30
80 neutral multiple teeth
for especially smooth cuts in solid
wood and particle board.
H Saw blade TCT 315 x 2.8 x 30
48 universal alternate bevel teeth
for all woods and wood-derived
smaterials.
I Roller Stand RS 420
J Roller Stand RS 420 W
K Roller Stand RS 420 G
The saw's packing can be 100% recy-
cled.
Worn out electric tools and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.
A
Danger!
Before carrying out any fault
service or maintenance work, always:
1. switch machine OFF;
2. unplug power cable;
3. wait for saw blade to come to
standstill.
Check that all safety devices are
operational again after each fault
service.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
−
switch on again.
No mains voltage:
−
check cables, plug, outlet and mains
fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
−
remove cause for overheating, wait
for a few minutes, then start saw
again.
Motor supply voltage too low:
−
use a shorter extension cable or
extension cable with larger lead
cross section
(
≥
1.5 mm
2
).
−
Have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
−
replace saw blade (see chapter
"Care and maintenance").
Chip build-up in the chip case
No, or dust collector of insufficient
capacity connected (see "Dust collector"
in chapter "Operation"):
−
connect dust collector, or
−
increase suction capacity.
Sliding plate of chip case closed:
−
open sliding plate
Height adjustment mechanism of saw
blade working stiff
Spindle of height adjustment mechanism
gummy:
−
clean spindle and spray with Care
and Maintenance Spray (see chap-
ter "Care and maintenance").
10. Repairs
11. Transportation
12. Available accessories
13. Environmetal protection
14. Trouble shooting