Honeywell INTELLIGUARD 9000 - Manual (Page 6)

INTELLIGUARD 9000™ SECURITY SYSTEM
74-3035—2 6
Communication: RS-485 receiving and transmitting signals.
Enclosures:
BIC-2 Input Module: Plastic polycarbonate. White with white
actuators.
BIC-2 HU Input Module: Plastic polycarbonate. White with red
actuators.
Dimensions: 5 in. (127 mm) wide x 1-3/4 in. (44 mm) high x
1 in. (25 mm) deep.
Weight: 2-7/8 oz (0.08 kg).
Approvals: UL, ULC, CE.
Multiple Output Module
The I9000 activates alarms
such as sirens, bells, lights, or
buzzers with the multiple
output module (MOM). Each
MOM activates a maximum of
eight alarms or notification
devices. The I9000 CU
supports four MOMs per
communication line for a
maximum of eight per system.
The MOM annunciates which outputs are active on a 7-
segment LED local display independently of the I9000 control
unit, provided the corresponding MOM parameter has been
enabled. If several outputs are active, the local display
automatically scrolls and displays all active outputs.
NOTE: The display indicates whether the function is active,
not whether the output is open or closed.
For installation or service, three onboard switches—in
conjunction with the LED display—allow the technician to
configure the unit. In this mode the MOM annunciates the
programmed output type for each output which can then be
modified using the switches.
Features
• Enclosure tamper switch.
• Eight independently programmable outputs—three
output types:
— Output normally off—on when the I9000 linked
function is active.
— Output normally on—off when the I9000 linked
function is active.
— Output normally off—pulsates as long as the
I9000 linked function is active.
— Interface is via three on-board push button
switches and the 7-segment display.
• Serial numbered device, no address switch setting
required—learned using the programming interface in
conjunction with a CC2 Keypad or using PRO9000.
• Tamper transmission status.
Model: 8003-286 Multiple Output Module (MOM).
Electrical Ratings:
Nominal Operating Voltage: 12 Vdc to 15 Vdc.
Operating Voltage: 10 Vdc to 18 Vdc.
Minimum Operating Current: 13.9 mA at 14.5 Vdc (outputs set
to Type 0 or 3, outputs not active, parameter 0 = 0, tamper
= normal, all switched loads powered separately).
Maximum Operating Current: 98.7 mA at 14.5 Vdc (all output
drivers powered on (outputs set to Type 0, outputs active)
parameter 0 = 1, tamper = normal, eight displayed,
switched loads powered separately).
Maximum Switched Current per Output: 50 mA externally
powered at 14.5 Vdc.
Maximum Output Terminal Voltage Drop: 1.0V (opto-coupler
in the ON state).
Maximum Output Terminal Voltage: 30V (opto-coupler in the
OFF state).
Annunciation:
Display: 7-Segment LED.
Information:
Communication Status: Unit must be in tamper alarm.
All active outputs: Unit must be in tamper alarm or the
respective parameter must be enabled.
Output Type: Normally open, normally closed, or pulsating
during local programming. Unit must be in tamper
alarm.
Communication: RS-485 receiving and transmitting signals.
Enclosure: Plastic polycarbonate base, ABS plastic cover.
Dimensions: 6-7/8 in. (1.74 mm) wide x 3-3/4 in. (94 mm)
high x 1 in. (25 mm) deep.
Weight: 0.64 lb (0.29 kg).
Approvals: UL, ULC.
Hall Effect Door Switch
Each Hall Effect Door Switch IV
(HEDS IV) is a high security
intelligent door contact/
detector. It consists of two
parts, the sensor (see photo—
right side) and the magnet
assembly (see photo—left
side). The sensor is mounted
on the door frame and the
magnet assembly attaches to the door. When the door opens,
the HEDS IV sends a signal directly to the I9000 Control Unit.
NOTE: Maximum gap permitted between the sensor and
magnet assemblies is 3/16 in. (4.76 mm).
Model: 8003-283 Hall Effect Door Switch IV (includes both
the 8003-280 and 8003-282).
Electrical Ratings:
Nominal Operating Voltage: 12 Vdc to 15 Vdc.
Maximum Operating Voltage: 10 Vdc to 18 Vdc.
Normal Operating Current: 7 mA at 14.5 Vdc.
Maximum Operating Current: 12 mA at 14.5 Vdc (learn
mode).
Weight: 0.68 lb (0.31 kg).
Accessory (optional): 8003-302 HEDS IV L Bracket (white
aluminum).
Approvals: UL, ULC, CE.