Remote control functions – Harman-Kardon AVR45 User Manual

Page 16

Advertising

Remote Control Functions

Memory Button:

Press this

button to enter a radio station into
the AVR45’s preset memory. After
pressing the button the MEMORY
indicator

N will flash, and you then

have five seconds to enter a present
memory location using the

Numeric

Keys

l. (See page 26 for more

information.)

NOTE:

Although the word “Sleep”

appears above this button, it refers
to control of devices other than the
AVR45. Use the

Sleep

button

` to

control the AVR45’s Sleep function.

Info Button:

This button does

not function with the AVR45, but it is
available for use with other devices.

Light Button:

Press this button

to activate the remote’s built-in back-
light for better legibility of the buttons
in a darkened room.

Tuner Mode:

Press this button

when the tuner is in use to select
between automatic tuning and
manual tuning. When the button is
pressed so that the AUTO indicator
O goes out, pressing the

Tuning

buttons

t will move the frequency

up or down in single-step incre-
ments. When the FM band is in
use, pressing this button when a
station’s signal is weak will change
to monaural reception, as indicated
by the MONO indicator

Q. (See page

26 for more information.)

Clear Button:

This button does

not function with the AVR45, but it is
available for use with other devices.

Preset Up/Down:

When the

tuner is in use, these buttons scroll
through the stations that have been
programmed into the AVR45’s mem-
ory. When many source devices,
such as CD players, VCRs and cas-
sette decks, are selected using the

Device Control Selectors

these buttons will normally function
as chapter step or track advance.

Tuning Up/Down:

When the

tuner is in use, these buttons will
tune up or down through the select-
ed frequency band. If the

Tuner

Mode

button

q has been pressed

so that the AUTO indicator

O is illu-

minated, pressing these buttons will
cause the tuner to seek the next sta-
tion with acceptable signal strength
for quality reception. When the AUTO
indicator

O is NOT illuminated,

pressing these buttons will tune sta-
tions in single-step increments. (See
page 26 for more information.)

Transport Controls:

These con-

trols do not control any functions of
the AVR45, but they are used exten-
sively when operating a wide variety
of CD players, cassette decks and
VCRs. (See page 28 for information
on programming the remote to utilize
these buttons.)

Delay/Prev Ch.:

Press this but-

ton to begin the process for setting
the delay times used by the AVR45
when processing surround sound.
After pressing this button the delay
times are entered by pressing the

Set

button

i, and then using the

⁄

buttons

g to change the set-

ting. Press the Set button again to
complete the process. (See page 20
for more information.)

›

/Digital Button:

This button is

used to select the type of digital input
used with any one of the input sources
connected to the AVR45. After press-
ing this button, use the

⁄

buttons

g to make your selection between
OPTICAL

E or COAXIAL G digital.

Press the

Set

button

i to enter

your choice. (See page 24 for more
information.)

Speaker Configuration:

Press

this button to begin the process of
configuring the AVR45’s Bass
Management System for use with
the type of speakers used in your
system. Once the button has been
pressed, use the

⁄

buttons

g to

select the channel you wish to set up.
Press the

Set

button

i, and then

select another channel to configure.
When all adjustments have been
completed, press the Set button
twice to exit the settings and return
to normal operation. (See page 17
for more information.)

Surround Mode Selector:

Press

this button to begin the process of
changing the surround mode. After
the button has been pressed, use
the

⁄

buttons

g to select the

desired surround mode. (See page
24 for more information.) Note that this
button is also used to tune channels
when the TV is selected using the

Device Control Selector

When the AVR45 remote is being pro-
grammed for the codes of another
device, this button is also used in the
“Auto Search” process. (See page 28
for more information on programming
the AVR45 remote.)

Volume:

Press these buttons to

raise or lower the system volume.

Sleep Button:

Press this button

to place the unit in the Sleep mode.
After the time shown in the display,
the AVR45 will automatically go into
the Standby mode. Each press of
the button changes the time until
turn-off in the following order:

Note that this button is also used
to change channels on your TV
when the TV is selected using the

Device Control Selector

min

OFF

AVR45 om (G).Eng,Fr 4/16/99 11:41 AM Page 13

Advertising

Popular Brands

Popular manuals