Document Outline

• 1. INTRODUCTION
  • OEM Installations
  • Warning
  • About this Guide
  • Menu Descriptions
• 2. WIRING OVERVIEW
  • Recommended Wiring Practices
  • Power Requirements
  • Grounding
  • +5V Excitation
  • Thermocouple Harness Preparation
  • Harness Mating
  • 37-Pin Female EMS Harness
  • 25-Pin Male EMS Harness
• 3. TRANSDUCER INSTALLATION
  • Tools and Equipment Required
  • Exhaust Gas Temperature (EGT) Probes
    • ROTAX ENGINES
    • ALL ENGINES
  • Cylinder Head Temperature (CHT) Probes
    • LYCOMING/CONTINENTAL
    • ROTAX
    • JABIRU
  • Tachometer
    • TACHOMETER TRANSDUCER
    • P-LEAD PICKOFF (LYCOMING AND CONTINENTAL)
    • TRIGGER COIL (ROTAX)
    • ALTERNATOR WIRE (JABIRU)
    • DIGITAL IGNITION AND OTHER PICKOFFS
  • Manifold Pressure Sensor
  • Oil Pressure Sensor
    • DYNON-SUPPLIED OIL PRESSURE SENSOR
    • JABIRU AND ROTAX OIL PRESSURE
  • Oil Temperature Sensor
  • Fuel Pressure Sensor
  • Fuel Flow Sensor
    • GENERAL PLACEMENT RECOMMENDATIONS
    • FLOSCAN TRANSDUCER INSTALLATION
    • EI “RED CUBE” INSTALLATION
    • ROTAX PLACEMENT RECOMMENDATIONS
  • Fuel Level Sensor
    • RESISTIVE FUEL LEVEL SENSOR
    • CAPACITIVE FUEL LEVEL SENSOR
  • Ammeter Shunt
  • General Purpose Inputs
    • OUTSIDE AIR TEMPERATURE SENSOR
      • Mount Location
      • Mounting Instructions
      • Wiring Instructions.
    • CARBURETOR TEMPERATURE SENSOR
    • FUEL LEVEL (RESISTIVE) SENSORS
    • ROTAX CHT SENSORS
    • TRIM AND FLAPS POSITION POTENTIOMETERS
    • COOLANT PRESSURE SENSOR
    • COOLANT TEMPERATURE SENSOR
    • GENERAL PURPOSE TEMPERATURE SENSOR
  • Contacts
  • General Purpose Thermocouple
• 4. INSTRUMENT INSTALLATION
  • Power Bus Wiring
  • Serial Communication Cables
    • PC USB CONNECTION
    • EMS SERIAL HARNESS
  • SL30 and/or GPS connection
    • IF YOU OWN ONLY AN EFIS-D10A OR EFIS-D100
    • IF YOU OWN TWO EFIS-ONLY UNITS
    • IF YOU OWN ONLY AN EMS-D10 OR EMS-D120
    • IF YOU OWN AN EMS AND AN EFIS (NOT FLIGHTDEK-D180)
    • IF YOU OWN ONLY A FLIGHTDEK-D180
    • IF YOU OWN A FLIGHTDEK-D180 AND AN EFIS
  • External EMS Warning Light
  • Audio Alert Outputs
  • Dynon Smart Avionics Bus (DSAB) Wiring
  • Panel Location and Mounting
    • OPTION 1: NO MOUNTING BRACKET
    • OPTION 2: FLUSH-MOUNT BRACKET
• 5. EMS CONFIGURATION
  • Full-Page Setup Menu Overview
  • Alarm and Color Threshold Configuration
  • Global Parameters Setup
  • Engine Type Configuration
    • ENGINE TYPE: LY/CON
    • ENGINE TYPE: ROTAX
    • ENGINE TYPE: OTHER
  • Fuel Level Calibration
  • Trim Calibration
  • Flaps Calibration
  • Tachometer
  • Manifold Pressure
  • Oil Pressure
  • Oil Temperature
  • Exhaust Gas Temperature (EGT)
    • SPAN ALARMS
  • Cylinder Head Temperature (CHT)
    • SPAN ALARMS
    • SHOCK COOLING ALARMS
  • Fuel Level
  • Fuel Pressure
  • Fuel Flow
  • Voltage
  • Current
  • General Purpose Inputs
    • ROTAX CHT
    • RESISTIVE FUEL LEVEL
    • CARBURETOR TEMPERATURE
    • COOLANT TEMPERATURE
    • COOLANT PRESSURE
    • OUTSIDE AIR TEMPERATURE SENSOR
    • AILERON TRIM
    • ELEVATOR TRIM
    • RUDDER TRIM
    • FLAP POSITION
    • GENERAL PURPOSE TEMPERATURE
  • Contacts
  • General Purpose Thermocouple
• 6. DSAB CONFIGURATION
  • Network Concepts
  • Example Networks
  • Initial Setup
  • Network Status
• 7. APPENDIX
  • Appendix A: Capacitance-to-Voltage Converter Installation
    • GENERAL INSTALLATION RECOMMENDATIONS
  • Appendix B: Troubleshooting
    • INSTRUCTIONS FOR RETURN
  • Appendix C: Weights
  • Appendix D: EMS-D10 Specifications