Document Outline

• OWNER'S MANUAL
• Water Softener
  • ONE YEAR LIMITED WARRANTY ON WATER SOFTENER
  • THREE YEAR LIMITED WARRANTY ON ELECTRONIC PARTS
  • TEN YEAR LIMITED WARRANTY AGAINST LEAKS
  • This warranty covers only defects in material and workmanship. Sears will NOT pay for:
  • Disclaimer of implied warranties; limitation of remedies
  • Sears, Roebuck and Co., Hoffman Estates, IL 60179 Sears Canada Inc., Toronto, Ontario, Canada MSB 2B8
• Questions?
  • Call the Kenmore Water Line at 1-800-426-9345 or visit KenmoreWater.com
    • For repair or replacement parts, call toll-free 1-800-366-7278 See back cover for other Sears service numbers.
  • Safety Guides
  • Unpack and Check Your Carton
    • INSPECT SHIPMENT
    • WHERE TO INSTALL THE WATER SOFTENER
    • DRAW IN YOUR PIPES AND FITTINGS
    • PIPE, FITTINGS, OTHER MATERIALS NEEDED
      • FIG. 6
      • BEFORE INSTALLING CHECKS & TESTS
  • Assemble Drain Port Elbow
    • A disposable piece of tubing has been installed in the “drain” port of your new water softener to protect it during shipping. Please do the following:
  • Install Single Bypass Valve
    • ASSEMBLE INLET OUTLET ADAPTORS,
    • OR SINGLE BYPASS VALVE
    • INSTALL SEARS BYPASS VALVE AND / OR THE INLET OUTLET THREADED ADAPTORS
      • FIG. 7
      • FIG. 8
    • BYPASS VALVE:
    • INLET AND OUTLET THREADED ADAPTORS:
    • INSTALLING BYPASS VALVE, AND/OR INLET AND OUTLET THREADED ADAPTORS
  • Install Single Bypass Valve
    • INSTALLING HOLDING CLIPS
  • Install 3-Valve Bypass
    • INSTALLING 3 VALVE BYPASS AND PIPES
  • Locate Water Softener and Connect Pipes
    • POSITION SOFTENER INTO PLACE
    • CONNECT THE SOFTENER
  • Connect Valve and Salt Tank Drains
    • CONNECT THE VALVE DRAIN HOSE
    • CONNECT SALT TANK OVERFLOW TUBING
  • Leak Test
    • 6. Close both cold water faucets.
    • FIG. 19
  • Electrical Requirements
    • INSTALL GROUNDING CLAMP BETWEEN THE SOFTENER IN AND OUT PIPES
    • ELECTRICAL POWER OUTLET FOR YOUR SOFTENER
    • PLUG IN THE TRANSFORMER
  • Install Covers and Restart Water Heater
    • INSTALL COVERS
    • RESTART THE WATER HEATER
      • YOUR PLUMBING INSTALLATION AND ELECTRICAL WORK ARE NOW COMPLETE.
  • Program The Timer
    • PROGRAM THE TIMER
      • FIG. 24
      • FIG. 25
  • Program The Timer
    • SET PRESENT TIME OF DAY
    • SET WATER HARDNESS NUMBER
    • SET REGENERATION TIME
      • FIG. 26
      • FIG. 27
      • FIG. 28
      • FIG. 29
  • The Water Softener
    • SANITIZE THE WATER SOFTENER
      • SANITIZE YOUR WATER SOFTENER AS FOLLOWS:
      • You can sanitize the softener with or without salt in the storage tank.
  • Adding Salt To The Storage Tank
    • ADDING SALT TO THE STORAGE TANK
    • WATER SOFTENING SALT WITH IRON REMOVING ADDITIVES
  • Check List
    • CHECK LIST OF STEP-BY-STEP GUIDES TO
    • EXTRA RECHARGE
    • RECHARGE NOW
    • RECHARGE TONIGHT
    • SALT MONITOR SYSTEM
      • To set this monitor system:
      • FIG. 35
    • ADDING SALT TO STORAGE TANK
    • • SALT EFFICIENCY
    • • CLEAN FEATURE
    • • CLEAN FEATURE MINUTES
    • • 97% FEATURE •12/24 HOUR CLOCK
    • • GALLONS / LITERS
    • • MAXIMUM DAYS BETWEEN REGENERATIONS
      • California Efficiency Requirement
      • FIG. 37
      • FIG. 38
    • TANK LIGHT
    • WATER FLOW THROUGH THE SOFTENER
      • FIG. 39
      • FIG. 40
      • FIG. 41
      • FIG. 42
  • Faceplate Timer Features
    • AVERAGE DAILY GALLONS or LITERS
    • RECHARGE TIME REMAINING AND VALVE POSITION INDICATORS
    • PROGRAM MEMORY
    • ERROR CODE
    • KENMORE’S ULTRA CLEANSING FEATURE
      • FIG. 45
      • FIG. 46
      • FIG. 47
      • FIG. 48
    • SOFT WATER SERVICE AND REGENERATION SERVICE
    • SOFT WATER SERVICE AND REGENERATION
    • SOFT WATER SERVICE AND REGENERATION AUTOMATIC BYPASS
      • ELECTRONICS
    • SALT BRIDGE
    • KEEPING THE WATER SOFTENER CLEAN
      • NOZZLE & VENTURI
      • 7. Install and tighten the cap, by hand only. Do not overtighten, which may break the cap or housing.
    • IRON FROM RESIN BED
      • PROTECT THE WATER SOFTENER FROM FREEZING
    • CHECKLIST TO HELP YOU SAVE MONEY
    • BYPASS VALVES
    • MODEL NO. 625.383760 - TIMER CODE H_32
      • FIG. 58
      • FIG. 59
    • ALWAYS MAKE THESE INITIAL CHECKS FIRST
  • Service Tech Information
    • FIG. 60
    • POSSIBLE PROBLEM
    • CODE
    • PROCEDURE FOR REMOVING ERROR CODE FROM FACEPLATE:
      • FIG. 61
    • TROUBLESHOOTING
    • VALVE POSITION INDICATORS:
      • TIMER PWA REPLACEMENT
      • FIG. 64
    • MANUAL ADVANCE REGENERATION CHECK
    • ROTARY VALVE SERVICE
    • TO RELIEVE PRESSURE:
    • DISASSEMBLY
    • SERVICING THE VALVE
    • ASSEMBLY
    • SERVICE CYCLE
    • FILL CYCLE
    • BRINING AND BRINE RINSE CYCLES
    • BACKWASH CYCLE
    • FAST RINSE CYCLE
  • Exploded View
  • Exploded View
  • Exploded View
• Get it fixed, at your home or ours!
  • 1-888-SU-HOGAR®