Document Outline

• Motion Control Engineering, Inc. 11380 White Rock Road Rancho Cordova, CA 95742 voice 916 463 9200 fax 916 463 9201 www.mceinc.com
• User Guide, Universal Serial Network
• Important Precautions and Useful Information
• Safety and Other Symbol Meanings
  • MCE Universal Serial Network
• In This Manual
• USN Installation
  • IMC, PTC, PHC Installation
    • Mounting the Board Assemblies
      • 1. Determine an appropriate location for the USN-BASE assembly. (Preferred location is in the upper left quadrant of the control enclosure.)
        • 2. Mount the board, facing outward, such that access to critical controller components is not blocked.
        • 3. For PTC/PHC programmable controllers, mount the M2C assembly near the USN-BASE assembly. (For a duplex, mount an M2C assembly in each controller enclosure but just one USN-BASE assembly in the enclosure of your choice.)
  • Motion 3000ES Installation
    • Mounting the Board Assemblies
      • 1. Determine an appropriate location for the USN-BASE assembly.
        • 2. Mount the board, facing outward, such that access to critical controller components is not blocked.
  • USN Power Connection, Elevators
    • 1. Connect the provided leads to the power transformer.
      • 2. Connect the power transformer leads to AC1/AC2 on the top right side of the USN-BASE assembly.
      • 3. Plug the power transformer into the AC receptacle in the controller. (Note: If alternate outlet is used, power must be in phase with controller 110 VAC.)
  • Power Connection, Escalators
    • 1. Using 18 AWG, white, teflon coated wires, connect HC-MPU, 16V1 to escalator board EC-MCB, CL1 and HC-MPU, 16V2 to EC-MCB CH1.
• Configuration
  • Device Type
    • 1. Set only the F7 switch UP.
      • 2. Press N until Device Type is displayed.
      • 3. Press S to select. Supported Device Types are:
      • 4. Select the Device Type.
      • 5. Press N to go to save menu. Press S to save.
      • 6. After the device type has changed, place the F7 switch down.
      • 7. Reset the USN board by pressing the RSTA button.
      • 8. After the device reboots, confirm new device type is selected.
  • Escalator Only
    • 1. Place switch F7 in the up position. Using the keypad as described earlier, set and save:
      • 2. Proceed to IP Setup.
  • IP Setup
    • Important
• Communication Connections
  • IMC
    • 1. Connect the external Ethernet cable to Ethernet Port A on the USN-BASE assembly.
      • 2. Connect the supplied C-RJ11/DB9M cable from a controller MC-RS (serial board) COM port to RS232 Port B (J7) on the USN-BASE assembly.
      • 3. Through the controller MPU board, set the connected COM port to media= serial and device= PC.
      • 4. On the MC-RS board, set the connected COM port slide switch to DCE.
      • 5. Press RSTA to reset the USN board so that it will read its new connections.
    • 1. Connect to the group controller using a CRT, terminal emulator, or TigerTerm software.
      • 2. Press F1, then 1 to get to the General configuration screen.
      • 3. Access the ICOM setting. Set it to the COM port connected to the MC-USN board. For example, if the MC- USN board is connected to COM2 on the MC-RS board, set the ICOM setting to COM2.
      • 4. Save.
      • 5. With the Function Switch F8 switch UP (all others down), press N to cycle through the menu to verify that information is correct.
  • PTC/PHC
    • 1. Connect the external Ethernet cable to Ethernet Port A on the USN-BASE assembly.
      • 2. The boards in the controller are connected along a ribbon cable bus. Connect the M2C assembly’s “From PCA” (JP3) to the last controller board on the bus using supplied ribbon cable.
      • 3. Connect the M2C assembly’s CAN2 port to the “Internal Network” (J5) connector on the USN-BASE assembly using the C-RJ-11 cable .
      • 4. For Duplex, connect both CAN2 ports on the M2C assembly to supplied splitter. Then plug the splitter into “Internal Network” (J5) connector on USN-BASE assembly.
      • 5. Press RSTA to reset the USN board so that it will read its new connections.
      • 6. With the Function Switch F8 switch UP (all others down), press N to cycle through the menu to verify that information is correct.
  • Motion 3000ES
    • 1. Connect the CAN bus wires from the three-wire terminal on lower right side of the HC- MPU (USN) board labeled “External Network” to escalator EC-MCB board, J12.
      • 2. Press RSTA to reset the USN board so that it will read its new connections.
• MC USN Information
  • Jumper Settings
  • Diagnostic LEDs
  • LCD and Keypad
  • Operating Displays
    • Troubleshooting
  • Diagnostic Menus
  • Configuration Menus
• Security Password Default for IMC Connections
  • 1. Disconnect the serial communication cable from the USN.
    • 2. Change the Device type setting from Swing Panel to a non-swing panel type (e.g. PCA Simplex A2K) and save.
    • 3. Reset board by pressing the RSTA button.
    • 4. Change Device type back to Swing Panel and save.
    • 5. Remove power from USN.
    • 6. Reconnect serial communication cable.
    • 7. Reconnect power to USN.
• KCE Functionality