Document Outline

• UPLIT039 Front Page.pdf
  • important safety instructions
  • save these instructions.
  • Please read and save these instructions. This manual contains important instructions for Chloride models:
  • Follow these instructions during installation and maintenance of the UPS and batteries.
  • If you have a problem with the UPS, please refer to this manual before calling the Technical Support Department. The Troubleshooting section on pages 20 and 53 address most UPS-related issues.
  • This equipment was tested and complies with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These lim...
  • Chloride Power Protection 28430 N Ballard Drive Lake Forest, IL 60045 USA Telephone: (847) 990-3228 Toll Free: (800) 239-2257 Facsimile: (800) 833-6829
• UPLIT039 TOC.pdf
  • Chapter 1 Chloride Introduction 1
  • Chapter 2 Display and Operation Elements (Active) 3
  • Chapter 3 Active Rackmount Series 7
  • Chapter 4 Active Installation and Commissioning 11
  • Chapter 5 Operational Characteristics (Active) 13
  • Chapter 6 Description of the Interface (Active) 16
  • Chapter 7 Maintenance (Active) 19
  • Chapter 8 Troubleshooting (Active) 20
  • Chapter 9 Technical Support for your Active UPS 21
  • Chapter 10 Active Tower and Rackmount Specifications 22
  • Chapter 11 Chloride Introduction 27
  • Chapter 12 Display and Operation Elements (E-Series) 29
  • Chapter 13 E-Series Installation and Commissioning 33
  • Chapter 14 Operational Characteristics (E-Series) 41
  • Chapter 15 Description of the Interface (E-Series) 44
  • Chapter 16 Maintenance (E-Series) 47
  • Chapter 17 Troubleshooting (E-Series) 48
  • Chapter 18 Technical Support for your E-Series UPS 49
  • Chapter 19 E-Series Specifications 50
• UPLIT039 Active and ESeries Rev 0.pdf
  • Chapter 1 Chloride Introduction
    • 1.1 Registering your Chloride Active UPS
    • 1.2 Technical Support and Service (Active)
    • 1.3 Safety Notes
  • Chapter 2 Display and Operation Elements (Active)
    • 2.1 Front
    • 2.2 Rear
      • 2.2.1 Active 700 and 1000
        • Fig. 1: Active 700 Rear View
        • Fig. 2: Active 1000 Rear View
      • 2.2.2 Active 2000 and 3000
        • Fig. 3: Active 2000 Rear View
        • Fig. 4: Active 3000 Rear View
  • Chapter 3 Active Rackmount Series
    • 3.1 Safety
      • 3.1.1 Intended use
      • 3.1.2 Further safety notes
    • 3.2 Installation and operating notes
      • 3.2.1 Selection of the mounting location
      • 3.2.2 Mechanical Attachment
        • Fig. 5: Mounting the rails at the body of the UPS or Battery-Pack.
    • Table 1. Battery Cabinets
      • 3.2.3 Connection of a battery pack
      • 3.3 Unit Rear View and Connections
        • 3.3.1 Active 700-19 and Active 1000-19
          • Fig. 6: Active700-19
          • Fig. 7: Active1000-19
          • Fig. 8: Battery Pack - BPActive1000-19
        • 3.3.2 Active 2000-19 and Active 3000-19
          • Fig. 9: Active2000-19
          • Fig. 10: Battery Pack - BPActive3000-19
        • 3.3.3 Active3000-19
          • Fig. 11: Active3000 -19
          • Fig. 12: BPActive3000-19
  • Chapter 4 Active Installation and Commissioning
    • 4.1 Commissioning of an External Battery Cabinet
    • Table 2. External Battery Packs
      • Fig. 13: Connection of Battery Extensions for devices Active 1000
  • Chapter 5 Operational Characteristics (Active)
    • 5.1 Ready for Operation Check
    • 5.2 Self Test
    • 5.3 Modes of Operation
      • 5.3.1 Normal Operation, Inverter On (Mains Available)
        • Fig. 14: Front Display Panel During Normal Operations (Mains Available)
      • 5.3.2 Battery Operation, Inverter On (Mains Failure)
        • Fig. 15: Front Display Panel During Battery Operation (Mains Failure)
      • 5.3.3 Bypass Operation, Inverter OFF (Overload > 140%)
        • Fig. 16: Front Display Panel During Bypass Operation (Overload > 140%)
  • Chapter 6 Description of the Interface (Active)
    • 6.1 Standard Interface COM A
      • Fig. 17: COM A signal Definition and Connection
    • Table 3. Interface COM A
      • 6.2 Optional Interface COM B
        • Fig. 18: Simplified Schematic of Interface Connections
  • Chapter 7 Maintenance (Active)
    • 7.1 Storage
      • 1. Connect the UPS to a grounded receptacle.
      • 2. Pull out the mains plug after 8 hours.
      • 3. Note the date of charging on the packing.
    • 7.2 Cleaning
  • Chapter 8 Troubleshooting (Active)
    • Table 4. Troubleshooting
  • Chapter 9 Technical Support for your Active UPS
    • 9.1 Chloride Technical Support
  • Chapter 10 Active Tower and Rackmount Specifications
    • Table 5. Chloride Active UPS North America
    • Table 6. Active Rackmount Technical Data for North American Models
      • 10.1 Battery Lifetime
        • Fig. 19: Typical lifetime of the batteries
  • Chapter 11 Chloride Introduction
    • 11.1 Registering your Chloride E-Series UPS
    • 11.2 Technical Support and Service (E-Series)
    • 11.3 Safety Notes
    • 11.4 Warning for E-Series E61, E101 and E203
  • Chapter 12 Display and Operation Elements (E-Series)
    • 12.1 Front
    • 12.2 Rear
      • 12.2.1 E-Series E61 and E101
        • Fig. 20: E41 or E61
        • Fig. 21: E81 or E101
      • 12.2.2 E-Series E203
        • Fig. 22: E203
  • Chapter 13 E-Series Installation and Commissioning
    • 13.1 Installation of the E-Series (Hardwired)
      • 1. Unpack and move E-Series UPS and battery cabinet(s), if supplied, into desired installation location.
      • 2. Adjust leveling jacks under the UPS and battery cabinet(s) to remove wheels of the units from the floor and avoid movement of connections.
      • 3. Turn off input and output breakers on the back of the UPS and any battery cabinets to be used.
      • 4. Turn off and isolate the power source to be used for the UPS input using proper lock-out/tag-out procedures.
      • 5. Confirm that the power source to be used for the UPS is 208 V (208/120 3 f for E203).
      • 6. Remove the connection plate on the back of the UPS to expose connection terminals.
      • 7. Wire input of the UPS by first connecting ground (earth) wire to GND (ground) terminal. Next, connect the input power leads t...
      • 8. If the UPS does not have an attached Power Distribution Unit (PDU), wire the output of the UPS to appropriate load as follows:
      • 9. Connect the UPS to the battery cabinet(s) (if required)
      • 10. Carefully replace the connection plate(s) on the battery cabinet and the UPS, making sure that no wires are pinched or damaged.
      • 11. Confirm that all input and output breakers on the UPS and battery cabinet(s) are in the OFF position.
      • 12. Restore power source to the UPS.
    • Table 7. Minimum Requirements for E-Series UPS Installation
      • Fig. 23: Wiring Diagram for the E61
      • Fig. 24: Wiring Diagram for the E101
      • Fig. 25: Wiring Diagram for the E153 and E203
      • Fig. 26: E203 Power System
      • 13.2 Commissioning of the E-Series
        • 1. Before using the device, charge the batteries for 8 hours.
        • 2. After charging, connect the loads to the UPS.
        • 3. When the signal interface is used, then the connection cable (accessories) is linked between UPS and computer system. Please see instructions in the documentation for the accessories.
        • 4. Switch on the loads.
        • 5. Switch on the UPS by operating the switch | on the front panel.
      • 13.3 Starting Up the E-Series
        • 1. Switch on the input circuit breaker on the back of the UPS.
        • 2. When connected to the mains, the batteries automatically begin charging. The UPS may be used immediately, however, full run time will not be available until the batteries are fully charged
        • 3. Before using the device, charge the batteries for 8 hours.
        • 4. After battery charging is completed, switch on the output circuit breaker at the rear side of the UPS. The loads are now supplied by the UPS.
        • 5. If a signal interface cable is used, connect the cable (accessory) between the UPS and the computer system. Please observe further instructions in the documentation for the accessory.
        • 6. Switch on the loads.
        • 7. Switch on the UPS by operating the switch | at the front plate.
      • 13.4 Commissioning of an External Battery Cabinet
    • Table 8. External Battery Packs
      • Fig. 27: Connection of an External Battery Cabinet to Type E61
      • Fig. 28: Connection of an External Battery Cabinet to Type E101
      • Fig. 29: Connection of an External Battery cabinet to Type E203
    • Table 9. Technical data of the connection cable
  • Chapter 14 Operational Characteristics (E-Series)
    • 14.1 Ready for Operation Check
    • 14.2 Self Test
    • 14.3 Modes of Operation
      • 14.3.1 Normal Operation, Inverter On (Mains Available)
        • Fig. 30: Front Display Panel During Normal Operations (Mains Available)
      • 14.3.2 Battery Operation, Inverter On (Mains Failure)
        • Fig. 31: Front Display Panel During Battery Operation (Mains Failure)
      • 14.3.3 Bypass Operation, Inverter OFF (Overload > 140%)
        • Fig. 32: Front Display Panel During Bypass Operation (Overload > 140%)
  • Chapter 15 Description of the Interface (E-Series)
    • 15.1 Standard Interface COM A
      • Fig. 33: COM A signal Definition and Connection
    • Table 10. Interface COM A
      • 15.2 Optional Interface COM B
        • Fig. 34: Simplified Schematic of Interface Connections
      • 15.3 Emergency Power Off (EPO)
  • Chapter 16 Maintenance (E-Series)
    • 16.1 Storage
      • 1. Install the hard-wire connections according to chapter 13 “E-Series Installation and Commissioning” on page 33 at an appropriate source. Switch on the input circuit breaker at the rear of the device for hard- wired connection.
      • 2. Switch off the input circuit breaker of the UPS. Then remove the connections of the UPS in an inverted sequence to what is described in chapter 13 “E-Series Installation and Commissioning” on page 33.
      • 3. Note the date of charging on the packing.
    • 16.2 Cleaning
  • Chapter 17 Troubleshooting (E-Series)
    • Table 11. Troubleshooting
  • Chapter 18 Technical Support for your E-Series UPS
    • 18.1 Chloride Technical Support
  • Chapter 19 E-Series Specifications
    • Table 12. Chloride E-Series UPS North America
      • 19.1 Battery Lifetime
        • Fig. 35: Typical lifetime of the batteries
      • 19.2 Optional Power Distribution Units (PDU) available 4 -10 kVA.
        • Fig. 36: Optional Power Distribution Units