Document Outline

• Vector Control
• Section 1: Parameterization of Base Drive
• Section 2: Parameterization of Rectifier
• Section 3: Simovis Trace Setup Method
• Section 4: When Should a Drive be re-Tuned
• We reserve the right to modify functions, technical data, standards, drawings and parameters.
• We have checked the contents of this document to ensure that they coincide with the described hardware and software. However, deviations cannot be completely ruled-out, so we cannot guarantee complete conformance. However, the information in this docum
• e-mail: mailto:[email protected]
• Note:
• Electrical equipment has parts an components which are at hazardous voltage levels.
• Section 1:
  • • • • • • • • Parameterization of Base Unit
• Vector Control
• Power Section Definition
  • Unit List
  • 3 AC 200V to 230V
    • • • • 6SE7021-1CA60
• 1.2 Factory Reset
• 1.3 Basic Start-up without Motor Connected to Load
  • Connect External Wiring as connection diagram.
  • Step 1: Dry set of contacts between terminals X101, pin#1 and pin#5 for Local/Remote Mode Selection. Jumper if not required.
  • Step 3: Dry set of contacts between terminals X101, pin#1 and pin#9 for Source of Main Start/Stop Selection.
  • Step 5: Dry set of contacts between terminals X101, pin#1 and pin#6 for Fixed Speed or Preset Speed Selection. Leave open if not required. Speed value is determined by P402. A selection of P402=100% will be a full speed reference setpoint.
  • 1.3.2 Volts/Hz with Encoder
    • P100 = 0
    • P151 = ?
  • Additional Connection for +15 Vdc Encoder.
  • Step 10: Set Speed Reference to 20%.
  • Step 11: Provide Start command. Note that if Signal A and Signal B are reversed, the motor will accelerate rapidly.
  • Step 12: Connect the motor to the load, unless the plan is to change to Vector Control.
  • 1.3.3 Vector Control without Encoder Feedback
    • P100 = 3
    • Wait
    • Wait
  • Step 10: Set Speed Reference to 20%, and monitor speed feedback r000, current feedback r004, and actual DC BUS r006. If stable increase speed in increments and continue to monitor feedbacks.
    • P100 = 4
    • P060 = 1
    • Wait
    • Wait
  • Step 11: Set Speed Reference to 20%, and monitor speed feedback r000, current feedback r004, and actual DC BUS r006. If stable increase speed in increments and continue to monitor feedbacks.
    • • • • • • • Parameterization of a Rectifer Unit
• Vector Control
• Power Section Defintion
• Factory Reset
• Basic Start-up
• Rectifier or Regen without auto-transformer
• Regen with auto-transformer
• 2.0 Power Section Definition
  • Unit List
  • 3 AC 380V to 460V
    • • • • 6SE7038-2EH85-0AA0
          • 6SE7041-0EH85-0AA0
          • 6SE7041-3EK85-0AA0
          • 6SE7041-8EK85-0AA0
  • 3 AC 500V to 575V
    • • • • 6SE7037-7FH85-0AA0
          • 6SE7041-0FH85-0AA0
          • 6SE7041-3FK85-0AA0
          • 6SE7041-5FK85-0AA0
          • 6SE7041-8FK85-0AA0
          • 6SE7037-7HH85-0AA0
          • 6SE7041-0HH85-0AA0
          • 6SE7041-3HK85-0AA0
          • 6SE7041-5HK85-0AA0
          • 6SE7041-8HK85-0AA0
  • 3 AC
  • 3 AC
  • 3 AC
• 2.1 Factory Reset
• 2.2 Basic Start-up (Regenerative Rectifier without Autotransformer)
  • • P052 = 5
    • P071 = 460
  • Connect External Wiring as connection diagram.
  • Step 1: Dry set of contacts between terminals X101, pin#6 and pin#13 for Local/Remote Mode Selection. Jumper if not required.
  • Step 3: Dry set of contacts between terminals X101, pin#6 and pin#9 for Source of Main Start/Stop Selection.
• 2.3 Basic Start-up (Regenerative Rectifier with Autotransformer)
  • • P052 = 5
    • P071 = 460
• Vector Control
• Vector Control
• 4.0 Conditions that would merit re-tuning the drive
  • If tuning parameters P103, P116, P120, P223, P235, P236, P240 and P471 had been recorded prior to the CUVC card being replaced.