FORD SK5W7J-19A361-AA - Manual (Page 24)

24/42 SK5W7J-19A361-AA © Copyright Ford 2005 2W7Z-16A901-AA
Rev Date- 8/29/05
Securilock (PATS) Interface Programming and Remote Start Operation Test
(two programmed PATS ignition keys are required for this step)
NOTE: This step does not apply to Econoline, SuperDuty Pick-ups and Escort
A. Sitting in the driver seat, be prepared to press the brake pedal to shut down the remote starter system.
B. Using the first key, turn the ignition on, wait for the THEFT light to turn off, then turn the ignition off and remove key from the ignition
switch.
C. Using the second key, turn the ignition on, wait for the THEFT light to turn off, then turn the ignition off and remove key from the ignition
switch.
D. Activate the remote start function using the PowerCode remote control transmitter.
The system should flash the parking lights and chirp the horn one time, pause for four seconds then start then start the engine.
E. After the engine is started. Press the brake pedal to shutdown the engine.
The Securilock interface is now programmed. If the theft light begins flashing rapidly and/or the engine does not crank or cranks but
will not start, refer to the troubleshooting information below.
F. Open the hood.
G. Sitting in driver’s seat, be prepared to press the brake pedal, activate the start function.
The system should chirp the horn two (2) times and abort the start sequence.
H. Close the hood.
I. Place ignition key in the ignition cylinder.
J. Again, Sitting in driver’s seat, be prepared to press the brake pedal and activate a start sequence.
The system should chirp the horn one (1) time pause four seconds, then chirp the horn two (2) times and abort the start sequence.
In steps G and J above, the engine MUST NOT start! If the system starts the engine in either steps G or J, check your hood tilt switch
installation and key-in-sense connection.
Troubleshooting steps:
A. If the Securilock interface fails to program (theft light flashing), check the following:
When programming the Securilock Interface timing is important, make sure that you:
1. Turn the ignition on with the second key within 5 seconds of the theft light going out on the first key;
2. Engage the remote start within 5 seconds of the theft going out on the second key;
3. Remove the second ignition key before engaging the remote starter.
NOTE: If a third (or more) PATS ignition key has been programmed to the vehicle using either the Ford NGS or WDS programmers, the “Add
Key” mode described in the installation manual may have been disabled. If this is the case, use the NGS or WDS programmer to either re-
enable the “add key” mode or program the Securilock Interface kit following the NGS or WDS procedure in the vehicle service manual for
adding a new PATS key.
B. If the theft light is solid and engine cranks but will not start:
Check all Ignition (Hot through run and crank circuits) and Heater (Run circuits). Make sure that the correct outputs from the
PowerCode module are connected to the correct vehicle circuits. Reversing the heater and ignition circuits from the PowerCode
system will not permanently damage the vehicle but may cause the remote start function to not work and/or set a PCM error codes
(which will cause the check engine light to stay on). If the check engine light stays on, use the NGS or WDS testers to identify which
fault code has been set. The fault code will help identify which circuit is not properly connected.
5
!
4 Tach (Idle speed) programming - Remote Start Systems Only
A. Make sure that the hood is closed before proceeding.
B. Enter option learn mode as described in step 2 of this section.
C. € RKE/VSS/RMST & RKE/RMST systems - Advance to option bank # 5 (8 chirps)
€ RMST system - Advance to option bank #2 (5 chirps) .
D. € RKE/VSS/RMST & RKE/RMST system - Advance to option #6;
€ RMST system - Advance to option #2.
E. Press and hold in the brake pedal and start the engine using the ignition key.
Allow the engine to settle to a normal idle speed. The system will chirp the horn every three (3) seconds if a valid tach signal is
detected.
F. After the engine has settled to a normal idle speed, press and release the programming/override button (the horn will honk four (4)
times) and turn the ignition key off.
NOTE: If the system is not chirping the horn every three (3) seconds after the engine has started, the system is not seeing a valid tach
signal. Check your tach connection (refer to the appropriate vehicle specific wiring diagram)
System Programming Instructions - Remote Start Systems