Freestyle S2S3 - Manual

ENGLISH
SHARK BUZZ 2.0
S1 S4
S2 S3
S1. Start/stop button
S2. Lap/reset button
S3. Mode button
S4. Light button
DISPLAY MODES:
The watch has six display modes:
HOME TIME, STOPWATCH, FOREIGN
TIME (T2), HOME TIME ALARM (A1),
FOREIGN TIME ALARM (A2) and TIMER
(TR).
To change from one display mode to
another, press S3 button once.
TO USE THE VIBRATION AND BEEP
FUNCTIONS:
The vibration and beep functions can
be activated individually or simultane-
ously. When the corresponding function
is activated, the watch will vibrate and
or beep when S1, S2 or S3 button is
pressed or when an alarm goes off.
TO TURN ON/OFF THE VIBRATION
AND BEEP FUNCTIONS:
In HOME TIME mode,
1. Press S1 button once to activate the
vibration function. Vibration indica-
tor will appear.
2. Press again to activate the beep
function. Beep indicator will
appear.
3. Press the third time to activate both
functions. Both of the indicators
will appear.
4. Press the fourth time to deactivate
both functions. Both of the indica-
tors will disappear.
TO SET THE TIME AND CALENDAR:
1. Press S3 button to select HOME
TIME / FOREIGN TIME mode.
2. Press and hold S2 button for
around 2 seconds, the second digits
will blink.
3. Press S1 button to reset the second
digits to zero.
4. Press S3 button, the hour digits will
blink.
5. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
6. Press S3 button once, the minute
digits will blink.
7. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
8. Follow the same pattern to set the
hour format, date, month and day
(of the week).
9. To set the hour format, press S1
button to toggle between 12-hour
and 24-hour format. The P.M. indi
cator may be displayed to indicate
the time period 12:00 A.M. – 11:59
P.M. in 12-hour format.
10. After finished making all the set-
tings, press S2 button to confirm.
NOTE: In FOREIGN TIME settings, only
the hour digits are open to setting.
All other settings are synchronized
between HOME TIME and FOREIGN
TIME mode.
HOME AND FOREIGN TIME DISPLAY:
To display the foreign time, press S3
button to select FOREIGN TIME mode.
The mode description (T2) will be
displayed.
TO USE THE STOPWATCH:
1. Press S3 button to select STOP-
WATCH mode.
2. The stopwatch will then be
displayed in its current status –
reset, running or stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, reset the
stopwatch to zero first.
Press S1 button to stop counting,
then press S2 button to reset.
For the measurement of elapsed time
In STOPWATCH mode,
1. Press S1 button to start counting.
2. To stop counting, press S1 button.
Press S1 button again to resume
from where it left off.
3. To reset to zero, press S1 button to
stop counting and then press S2
button.
For the measurement of split time
In STOPWATCH mode,
1. Press S1 button to start counting.
2. While the stopwatch is running,
press S2 button to register a lap.
The split time will be displayed and
the stopwatch is still running in the
background.
3. To display the currently accumu-
lated time, press S2 button again.
4. Repeat the last step until all the
laps have been registered.
5. To stop counting, press S1 button.
Press S1 button to resume from
where it left off.
6. To reset to zero, press S1 button to
stop counting and then press S2
button.
NOTE: The stopwatch can count up to a
maximum of 23 hours, 59 minutes and
59.99 seconds.
NOTE: You can leave the stopwatch
running while switching over to other
operating modes.
TO SET THE ALARM:
1. Press S3 button to select HOME
ALARM or FOREIGN TIME to set.
2. Press and hold S2 button for around
2 seconds. The hour digits will
blink.
3. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
4. Press S3 button, the minute digits
will blink.
5. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
6. After finished making all the set-
tings, press S2 button to confirm.
NOTE: The alarm will automatically be
activated after being set.
NOTE: The alarm will work according
to HOME TIME.
TO TURN ON/OFF THE ALARM AND
HOURLY CHIME:
1. Press S3 button to select HOME
ALARM or FOREIGN ALARM to set.
2. Press S1 button to activate the
alarm. Alarm indicator /
will appear.
3. Press again to activate the hourly
chime. Chime indicator will
appear.
4. Press the third time to activate both
functions. Both of the indicators
will appear.
5. Press fourth time to deactivate both
functions. Both indicators will
disappear.
WHEN AN ALARM OR CHIME GOES OFF:
A tune will be emitted by the hour
when the hourly chime function is
activated.
An alarm tune will be emitted at the
designated time for around 20 seconds
when the alarm is activated. To stop
the tune, press any button.
NOTE: The watch will not vibrate and
or beep to signal an hourly chime and
alarm unless the an vibration and or
beep function is activated.
TO SET THE TIMER:
1. Press S3 button to select TIMER
mode.
2. Press and hold S2 button for
around 2 seconds, the hour digits
will blink.
3. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
4. Press S3 button, the minute digits
will blink.
5. Press S1 button to set the minute
digits. Holding down the button
will speed up the process.
6. After finished making all the set-
tings, press S2 button to confirm.
TO USE THE TIMER:
1. Press S3 button to select TIMER
mode.
2. The timer will be displayed in its
current state – reset, running, or
stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, re-adjust
the timer first.
Press S1 button to stop counting,
then set the timer according to the
paragraph “TO SET THE TIMER”.
5. Press S1 button to start counting.
6. To stop counting, press S1 button.
Press S1 button again to resume
from where it left off.
7. After reaching zero in a countdown,
a tune will be emitted for around 20
seconds. To stop the tune, press
any button.
NOTE: You can leave the timer running
while switching over to other operating
modes.
TO USE THE BACKLIGHT:
Press S4 button to turn on the back-
light for around 3 seconds.