Freestyle FS81245 - Manual

TRIM
SHARK X 2.0
Shark X 2.0 IMS V1 21-10-2008
TO SET THE DIGITAL TIME AND
CALENDAR
1. Press S3 button to select time mode.
2. Press S2 button to toggle between
HOME TIME and FOREIGN TIME
mode to set.
3. Press and hold S2 button for two
seconds until the “SET” message
appears and the second digits blink.
4. Press S1 button to reset the second
digits to 00.
5. Press S3 button, the minute digits
will blink.
6. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
7. Press S3 button, the hour digits will
blink.
8. Press S1 button to set the hour
digits.
9. Follow the same pattern to set date,
month, day (of the week), hour
format and calendar format.
10.To set the hour format, press S1
button to toggle between 12-hour
and 24-hour format. The P.M.
indicator may be displayed to
indicate the time period 12:00A.M.
– 11:59 P.M. in 12-hour format.
11.To set the calendar format, press
S1 button to toggle between M-D
(month-date) and D-M (date-month)
format.
12.After finish making all the settings,
press S2 button to confirm.
NOTE: The chosen hour and calendar
formats will apply to both HOME TIME
mode and FOREIGN TIME mode.
NOTE: In FOREIGN TIME settings, only
minutes, hours, date, month and day
are open to setting.
TO SET THE ALARM TIME
1. Press S3 button to select alarm
mode.
2. Press S2 button to toggle between
HOME TIME ALARM and FOREIGN
TIME ALARM mode to set.
3. Press and hold S2 button for two
seconds until the “SET” message
appears and the minute digits blink.
4. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
5. Press S3 button, the hour digits will
blink.
6. Press S1 button to set the hour
digits.
7. After finish making all the settings,
press S2 button to confirm.
TO TURN ON/OFF THE ALARM
AND HOURLY CHIME
In alarm mode,
1. Press S2 button to toggle between
HOME TIME ALARM and FOREIGN
TIME ALARM mode to set.
Model FS81241
Model FS81242
Model FS81243
Model FS81244
Model FS81245
1. Hour Hand
2. Minute Hand
3. Second Hand
S1 - Start/stop button
S2 - Lap/reset button
S3 - Mode button
S4 - Light button
TO SET THE ANALOG TIME
1. Pull crown out to frist click position B.
2. Turn crown to set time.
3. Push crown back to position A.
DISPLAY MODES
The watch has four display modes:
HOME TIME (TIME), HOME TIME
ALARM (ALM1), STOPWATCH (STW)
and COUNTDOWN TIMER (TMR).
To change from one display mode to
another, press S3 button once. The
mode description will appear for 2
seconds before the selected mode is
activated.
HOME AND FOREIGN DISPLAY
To display FOREIGN TIME, press S2
button when HOME TIME is displayed.
The mode description (TM-2) will
appear shortly before FOREIGN TIME
is displayed. To change back to HOME
TIME, press S2 button.
To display the daily FOREIGN TIME
ALARM, press S2 button when HOME
TIME ALARM is displayed. The mode
description (ALM2) will appear shortly
before FOREIGN TIME ALARM is
displayed. To change back to HOME
TIME ALARM, press S2 button.
S1
S2
S4
S3
A
B
2
3
1
Model FS81241
Model FS81242
Model FS81243
Model FS81244
Model FS81245
1. Hour Hand
2. Minute Hand
3. Second Hand
S1 - Start/stop button
S2 - Lap/reset button
S3 - Mode button
S4 - Light button
TO SET THE ANALOG TIME
1. Pull crown out to frist click position B.
2. Turn crown to set time.
3. Push crown back to position A.
DISPLAY MODES
The watch has four display modes:
HOME TIME (TIME), HOME TIME
ALARM (ALM1), STOPWATCH (STW)
and COUNTDOWN TIMER (TMR).
To change from one display mode to
another, press S3 button once. The
mode description will appear for 2
seconds before the selected mode is
activated.
HOME AND FOREIGN DISPLAY
To display FOREIGN TIME, press S2
button when HOME TIME is displayed.
The mode description (TM-2) will
appear shortly before FOREIGN TIME
is displayed. To change back to HOME
TIME, press S2 button.
To display the daily FOREIGN TIME
ALARM, press S2 button when HOME
TIME ALARM is displayed. The mode
description (ALM2) will appear shortly
before FOREIGN TIME ALARM is
displayed. To change back to HOME
TIME ALARM, press S2 button.
2. Press S1 button once to activate the
alarm. Alarm indicator
will appear.
3. Press again to activate the hourly
chime. Chime indicator will
appear.
4. Press the third time to activate both
functions. Both of the indicators will
appear.
5. Press the fourth time to deactivate
both functions. Both of the
indicators will disappear.
WHEN AN ALARM OR HOURLY
CHIME GOES OFF
A tune will go off by the hour if the
hourly chime function is activated.
An alarm tune will be emitted for
around 20 seconds at the designated
time when the alarm is activated. To
stop the tune, press any button.
TO USE THE STOPWATCH
1. Press S3 button to select
STOPWATCH mode.
2. The stopwatch will then be displayed
in its current state – reset, running,
or stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, reset the
stopwatch to zero first.
Press S1 button to stop counting,
then press S2 button to reset
counter to zero.
For the measurement of elapsed time:
In STOPWATCH mode,
1. Press S1 button to start counting.
2. To stop counting, press S1 button
once. Press S1 button again to
resume from where it left off.
3. To reset to zero, press S1 button to
stop counting, then press S2 button
to reset the counter to zero.
For the measurement of split time:
In STOPWATCH mode,
1. Press S1 button to start counting.
2. While the stopwatch is running,
press S2 button once to register a
lap. The stopwatch is still running
in the background.
To display the currently accumulated
time, press S2 button again.
3. Repeat the last step until all the
laps have been registered.
4. To stop counting, press S1 button
once. Press S1 button again to
resume from where it left off.
5. To reset to zero, press S1 button to
stop counting, then press S2 button
to reset the counter to zero.
NOTE: You can leave the stopwatch
running while switching over to other
operating modes.
TO SET THE TIMER
1. Press S3 button to select TIMER
mode.
2. Press S2 button to alter the timer
setting among 1, 3, 5, 10, 15, 20, 25,
30, 45 and 60 minutes.
TO USE THE TIMER
In TIMER mode,
1. Press S1 button to start counting.
2. To stop counting, press S1 button
once. Press S1 button again to
resume from where it left off.
3. To reload the TIMER, press S1
button to stop counting and then
press S2 button.
4. After reaching zero in a countdown,
a tune will be emitted. To stop the
tune, press any button, the TIMER
will reload automatically.
NOTE: You can leave the timer running
while switching over to other operating
modes.
TO USE THE BACKLIGHT
Press S4 button to turn on the backlight
NOTE WHEN REPLACING BATTERIES
When changing the battery please note
that there is an INSULATOR PAD
between the small and large batteries.
Please make sure that you keep this
pad and reuse it in the same manner
after inserting the new batteries. The
INSULATOR PAD needs to be placed
on top of the small battery before
inserting the large battery. This pad
secures the small battery and ensures
the best contact for both batteries.
To reduce carbon foot print, these
Freestyle instructions are printed with
soy inks on recycled paper.
FS1059-01