FUNAI ZV450TT8 - Manual (Page 46)

46 EN
TIMER RECORDING
1 Press [TIMER PROG.].
2 Use [K / L] to select “New Program”,
then press [ENTER].
Timer Programming
1/1
MON JAN/01 10:00AM
Date Start End CH
New Program
• If there are 6 or more programs, use
[SKIP H / G] to change pages.
3 Use [K / L] to enter the date, then
press [B].
Date
JAN/02
CH
DTV125- 1
REC To Speed
DVD 2H
2H 2 : 00
Start
- - : - -
End
- - : - -
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
Daily
MON-SAT
JAN/01
JAN/31
MON-FRI
SAT
FRI
SUN
You can program the unit to record up to 12 programs
within a month in advance. Daily or weekly program
recordings are also available.
Before recording, make sure
• Set the clock before setting a timer programming.
• Insert a recordable disc with enough recordable space or
a cassette tape with an erase-protection tab.
Note
• If you have not set the clock yet:
“Clock Setting” menu will appear instead of the timer
programming list at step 1. Continue with the step 3
in “Manual Clock Setting” on page 29 before setting
a timer programming.
• Use [s / B] to move the cursor to the left and the
right in “Timer Programming” menu.
• If a basic recording or one-touch timer recording is in
progress on one component (e.g., VCR) and the timer
recording set for the other component (e.g., DVD) is
about to begin, the unit automatically switches to the
programmed channel for timer recording 2 minutes
before the programmed starting time, and the
recording in progress (for VCR) will be canceled
UNLESS their recording channels are the same. If their
recording channels are the same, the timer recording
will start without canceling the recording currently in
progress. In this case, the recording of the same
channel will be made on both DVD and VCR.
• Cancel the timer-standby mode by pressing
[T-SET] before operation for either DVD or VCR.
When finished operating, press [T-SET] to resume
the timer-standby mode.
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which is
not currently timer-programmed.
Guide to Timer Programming Display
Timer Programming
1/1
MON JAN/01 10:00AM 2H (1:00)
JAN/ 2/07 12:00 AM 125-1 SP
Date Start End CH
JAN/02 12:00AM 1:00AM DTV 125- 1
New Program
1
5
3
4
2
1. Title of a timer program (Contains date, time, channel,
recording speed of the program)
2. Current date and time
3. Recording speed and length of the recording
4. Timer program list
5. Total number of pages and current page (2 pages maximum)
1 2 3
4 5 6
7 8 9
0
POWER OPEN/CLOSE
DISPLAY
VCR DVD
CH
PLAY
STOP
REC/OTR
SKIP SKIP PAUSE
MENU/LIST TOP MENU
AUDIO
SETUP
X1.3/0.8
T-SET SEARCH
ENTER
DUBBING
CM SKIP
REC SPEED
TIMER PROG.
RETURN
CLEAR SPACE
DEF
DTV / TV
ABC .@/:
MNO JKL GHI
WXYZ TUV PQRS
INPUT
SELECT
OPEN/CLOSE
1 2 3
4 5 6
7 8 9
0
SPACE
DEF ABC .@/:
MNO JKL GHI
WXYZ TUV PQRS
T-SET
SETUP
ENTER
PLAY
TIMER PROG.
SKIP SKIP