FARGO electronic HDP600 - Manual (Page 363)

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.3) 16-1
Section 16: Index
A
About button, 7-23
absolute failure, 7-9
AC - Alternating Current, 15-1
accelerated wear/dye migration, 7-7
Accepted Card Compositions, 2-8
Accepted Card Thickness, 2-8
Access Card, 15-1
adhesion, 7-9
Adhesion, 15-1
adhesives, 7-5
Adjust Image Position controls, 7-43
Adjusting Card Thickness Lever, 7-4
Adjusting Lamination Sensor Calibration, 11-27
Adjusting Lamination Temperature Setting, 11-27
Adjusting the Flipper Offset, 11-24
Adjusting the LAM TOF and EOF, 11-26
Adjusting the Lamination Flipper Offset, 11-25
Agency Listings, 2-6
Algebraic, 7-28, 15-1
all Printers share all print jobs, 7-36
ANSI (American National Standards Institute), 15-1
Appropriate HDP Printer Driver Settings, 7-6
AS400, 15-1
ASCII (American Standard Code for Information
Interchange), 15-1
AT, 15-1
Attention screen, 2-21
Auto Eject 1st Error option, 7-62
auto eject option, 7-62
B
B (Black), 15-1
Barcodes, 15-2
batch print, 15-2
batch printing, 7-62
Battery Back-up, 15-2
Bi-directional, 15-2
BIOS (Basic Input/Output System), 15-2
Bit, 15-2
Bit map, 15-2
black graphics, 7-47
black text or barcodes, 7-47
Board, 15-2
Boot-up, 15-2
Buffer, 15-2
C
Cable, 15-2
Cache, 15-3
Calibrating, 15-3
Can
’t Find Card Error, 4-3
Cancel button, 2-19
Cancel Prompt, 4-2
Cancel soft key, 7-62
Card Capacity, 2-8
Card Cleaning Assembly, 2-16
Card Count, 4-19
Card Design, 2-23
card grid, 7-50
Card Hopper Jam, 4-2
Card Illustration, 7-43
Card Input Guide adjustment, 6-6, 7-10, 7-11
Card Input Hopper, 2-15, 2-24 , 2-25
Card Jam
Flipper, 4-3
Lam, 4-3
Card Jam, 4-3
Card Output Hopper, 2-15
Card Size, 2-23, 7-13, 7-14, 7-16
card stock selection, 7-5
Card Surface, 2-23
Card Thickness Adjustment Knob, 2-16
Card Type, 7-17, 7-18, 7-19
Card Type, 2-8
Card Type Custom options, 7-45
Card Type option, 7-6, 7-45
Card Type Selection, 7-6
card warping, 7-17
card's Magnetic Stripe/smart chip, 7-35
CD (Compact Disc), 15-3
Centronics, 15-3
Check Cards Error, 4-2
Check Film Error, 4-3
Check Lam Power, 4-7
Check Ribbon Error, 4-4
Clean inside Printer, 8-4
Clean outside of Printer, 8-4
Cleaning Cartridge, 8-6
Cleaning Roller, 8-6, 15-3
Cleaning Tape loop, 8-6
Clear Protective Overlay Panel, 2-22
Coercivity, 15-3
Coercivity option, 7-58
Color Bars YMC, 4-18
color correcting, 7-28
color matching, 7-28, 15-3
color matching algorithm, 7-28
color matching software, 7-28
Color Tone, 7-29
colors, 2-8
Communication Error, 4-10
Compressed air, 15-3
compressed Firmware Update file, 12-3
Contrast, 15-3
Contrast/Gamma, 7-39
Control panel, 15-3
Copies, 7-21
copyright/version information, 7-23
CR-100, 15-4
CR-100 patch size, 2-29
CR-79, 15-4
CR-80, 7-14
CR-80, 15-4