Furuno CH300 - Manual (Page 11)

CH300 Installation Check Sheet
Vessel Information CH300 System Information
Vessel Name: CH300 Model:
Type: Use: Serial Number:
Length: Registry: Shaft Travel:
Operating Speed: Hull Type: System Input Voltage:
Dealer Information
Dealer Name:
Address:
City, State, Zip:
Installed By:
Date:
Location:
Standard System – MU100C Display Check List
Are all cables and connections tight & strapped?
❏
Yes
❏
No
Is NMEA data connected and activated?
❏
Yes
❏
No
What NMEA devices are connected:
Has CH302 control head installation & operation been checked?
❏
Yes
❏
No
Is the unit grounded properly?
❏
Yes
❏
No
OR
Black Box System – VGA Display Check List
Are all cables and connections tight & strapped?
❏
Yes
❏
No
Does the monitor display the correct color palette?
❏
Yes
❏
No
Are the IF8000 dip switches set correctly?
❏
Yes
❏
No
Is NMEA data connected and activated?
❏
Yes
❏
No
What NMEA devices are connected:
Has CH302 control head installation & operation been checked?
❏
Yes
❏
No
Is the unit grounded properly?
❏
Yes
❏
No
CH303 Transceiver Unit Check List
Are all cables and connections tight & strapped?
❏
Yes
❏
No
Check and note actual input voltage
Is the unit grounded properly?
❏
Yes
❏
No
Motion Sensor or Incinometer Check List
Which sensor is being used, BS704 or MS100 or Sat Compass?
Where is the sensor located?
Has the sonar been programmed to look for the sensor?
❏
Yes
❏
No
Sonar Tube Installation Check List
Was a Furuno supplied sonar tube used?
❏
Yes
❏
No
If not, what was the ID of the sonar tube used?
What is the actual length of the sonar tube?
Where is the sonar tube mounted?
Is the sonar tube on or off the vessels centerline?
❏
On
❏
Off
Has a sonar tube air venting system been installed?
❏
Yes
❏
No
Has a forward sonar tube fairing been installed?
❏
Yes
❏
No
Motion Sensors, Inclinometers and
Longer Interconnect Cables
This valuable accessory unit must be mounted correctly to obtain any benefit from it:
a) Select a mounting location that is dry and vibration free
b) The selected location should be as close to the sonar hoist unit as possible
c) Mount the unit level (only compensating for normal vessel trim)
d) Line the unit up "fore and aft" accurately
e) Mount the unit "right side up" only
If a longer interconnect cable assembly is required, the following options are available:
Part number Description
MS1-CBL-15M 15 meter signal cable assembly
MS1-CBL-30M 30 meter signal cable assembly
MS1-CBL-50M 50 meter signal cable assembly
Note:
The MS100 compensates for any vessel pitching and rolling at sea. To properly set itself the
motion sensor must be powered up while the vessel is in a stable condition. This step is easi-
er to accomplish at the dock. Please get in the habit of powering up the entire CH300 system
prior to departing from the dock. This one easy step will ensure proper operation of the
MS100 and enhanced CH300 performance for the duration of the voyage.
Soundome Cover Removal and Replacement
Remember to detach or replace the soundome cover assembly, ONLY remove the 10
stainless steel Allen head cap screws! These are the cap screws that hold the soundome
cover assembly to the upper bronze housing.
The plastic cover cross head screws should never be touched! This cover has been factory
sealed and cannot be replaced in the field without destroying the soundome's watertight
integrity and warranty.
Once the soundome has been filled with oil, keep it in a vertical position to prevent any
internal seepage. If the soundome assembly has to be removed for repair or shipment, the oil
must always be removed.You may wish to retain the soundome packing material for future
use.
Page 1 Page 8