GE 200D8074P050 - Manual (Page 15)

About the ice and water dispenser.
(on some models)
GEAppliances.com
To Use the Dispenser
Select CUBED, CRUSHED or WATER.
Press the glass gently against the top
of the dispenser cradle.
The spill shelf is not self-draining. To reduce water
spotting, the shelf and its grille should be cleaned
regularly.
If no water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser arm for at least two
minutes to remove trapped air from the water line
and to fill the water system. To flush out impurities
in the water line, throw away the first six glassfuls
of water.
CAUTION: Never put fingers or any other objects
into the ice crusher discharge opening.
Locking the Dispenser
Press the LOCK or LOCK CONTROLS pad for
3 seconds to lock the dispenser and control panel.
To unlock, press and hold the pad again for
3 seconds.
Dispenser Light
The LIGHT pad turns the night light in
the dispenser on and off. The light also comes on
when the dispenser cradle is pressed. On some
models, if this light burns out, it should be replaced
with a 6 watt 12V maximum bulb.
Door Alarm
Use Door Alarm to sound if either door is open
for more than 3 minutes. The alarm will stop
once the door is closed. For LCD models, a popup
screen will appear. The alarm can be silenced
by touching the LCD screen.
LCD Models:
Access By: Home > Options > Information and
Settings > Settings > Door Alarm
Access By: Pressing ON.
Deactivate By: Pressing OFF.
Non-LCD Models:
Press the SET FEATURES pad once and DOOR
ALARM will blink. Press ON/OFF and the door
alarm will be set and the icon will turn solid. Press
ON/OFF again to turn the alarm off.
Spill Shelf
Consumer S
up
por
t
Troubleshooting T
ips
Operating Instructions
Safety Instructions
Installation Instructions
Precise Fill (on some models)
Quick Ice
This water dispenser is equipped with a feature
called “precise fill.” This feature allows you to
choose a precise amount of water (cups or
ounces) that you would like dispensed. Pints
and Liters are also available for LCD models.
LCD Models
Access By: Home > Options > Dispenser Options >
Precise Fill > Set Amount
Activate By: Using the arrow buttons to select
the desired amount. Press MORE UNITS to select
between CUPS, OUNCES, PINTS or LITERS.
Non-LCD Models
Press the PRECISE FILL CUPS/OZ pad.
The WATER pad will light and the CRUSHED
and CUBED ice pads will turn off. The last
unit used will be displayed.
Press the PRECISE FILL pad again to toggle
between cups and ounces.
If you selected OUNCES, press the or pad
to select the number of ounces you would like
to have dispensed between 2–99 ounces.
The default is 8 ounces.
If you selected CUPS, press the or pad
to select the amount you would like to have
dispensed. They are displayed as 1/4, 1/3, 1/2, 2/3
and 3/4, with the highest amount being 16 3/4
cups. The default is 1 cup.
Press the cup against the cradle and water
will begin dispensing. It will automatically
stop when the amount set has been
dispensed. The display will show the amount
of water dispensed, beep, then reset after 5
seconds.
NOTE: Do not leave the dispenser unattended
when water is being dispensed.
If you would like to stop dispensing water
before the specified amount has been
dispensed, just remove the cup from the
cradle. The display will show the amount that
has been dispensed for 5 seconds. If the cup
switch is pressed again within that time, the
dispenser will continue up to the set amount.
If not, the display will return to the set
amount.
When you need to speed up ice production, use
the Quick Ice feature. While this feature is turned on,
the freezer fan runs continuously for 48 hours, or
until the feature is turned OFF. During this period,
ice production will increase up to 40%. Models with
the integrated ice feature system require at FIRST
USE at least half an 8 oz. glass of ice to be dispensed
every 6 to 12 hours. This will help the icemaker fill
the bucket properly so that dispensing is better.
How to Use
LCD Models:
Access by: Home > Options > Freezer Options >
Quick Ice
Activate by: Pressing ON.
Deactivate by: Pressing OFF.
Non-LCD Models:
Press the SET FEATURES pad twice and QUICK ICE
will blink. Press ON/OFF to turn the feature on,
then again to turn it off.
15
>
>
> >