Graco 9651 & 9744 - Manual (Page 4)

5 374-7-99 6 8 7
Step 1.
Remove the mattress from your bassinet.
Step 2.
Unsnap the end flaps from your Pack ’N Play.
Step 3.
Pull back the fabric at one corner of the bassinet to find the
red spring latch.
Step 4.
Pull the red spring latch back
and lift up the tube.
Step 5.
Pull the tube out of the bassinet
and set aside.
Step 6.
Repeat steps 3, 4 and 5 to remove the other tube.
Step 7.
Use extreme
care when pulling the tubes
apart.
Pull the tubes apart by twisting
the tubes as you pull. Store the
tubes in the pockets in the
bassinet.
To Install Your Bassinet
PARTS LIST
CHECK that you have all the parts listed below
BEFORE assembling your bassinet.
No tools required.
Bassinet
Tube (2)
Tube (2)
Loop end Wire end
Red spring
latch end
Round end
To avoid SUFFOCATION, DO NOT use
extra padding such as a water mattress, mattress, or
pillows inside the bassinet. Use ONLY mattress
provided by Graco.
To help prevent heat build-up inside
the playard and to avoid overheating your child, when
using the bassinet DO NOT use a canopy.
Your bassinet is now ready to use.
To Remove Your Bassinet
To Use as a
Playard/Portable Crib
Place mattress into your unit
with padded side up.
Always use your unit with
mattress installed soft side up.
Slide the two
VELCRO ®
straps
through slots in bottom of Pack
’N Play and fasten to VELCRO ®
on underside. This will prevent
mattress from moving.
Your Pack ’N Play is ready to
use.
Step 4.
Install the end of the tube
without the red spring latch
by placing the loop end into
the slot in the plastic corner.
Step 5.
On the other end of the tube,
pull back on the red spring
latch and insert the loop into
the slot in the plastic corner.
Step 6.
Repeat steps 4 and 5 on the
other side of the bassinet.
Step 7.
Snap both of the end flaps of
the bassinet to the Pack ’N
Play with the eight snaps
(four on each end).
Step 8.
Cover soft side of mattress
with fitted sheet (on certain
models) and place the
mattress in the bassinet
soft side up. Push down
on the mattress to secure
the mattress to the VELCRO ®
on the bassinet.
DO NOT use your bassinet
without the mattress
provided by Graco.
At first your Pack ’N Play may be like a new pair of
shoes. You may need to break it in by slightly stretching
the netting and fabric. If the center does not stay down,
place some weight (several books) in the center of the
unit and let it stand overnight.
The four bassinet tubes are located in storage pockets
sewn into the bassinet itself.
Step 1.
Insert wire end of one tube
into the round end of a tube
with a red spring latch.
Repeat with other tubes.
Step 2.
Slide the assembled tubes
into the tunnels on the sides
of the bassinet.
Step 3.
Lift bassinet by the two tubes and lower it into the
Pack ’N Play. Make sure the printed warnings on
the end flap are facing up.
The loop ends must be in the slots in the
corners to secure the bassinet in the Pack ’N Play. Pull
up on the tube and bassinet to ensure that the tube is
in place.
Accessory Features
SIDE FLAP:
You can raise side flap if
desired.
Unfasten
VELCRO ® straps at
bottom of flap. Roll flap up.
Fasten in place with snap
loops at top.
WHEELS:
To apply the locks, push
DOWN on the levers.
To release the locks, lift UP
on the levers.
TOY BAG:
Toy bag snaps on end of
unit. Maximum weight
2 lbs (0.9 kg).
DO NOT machine wash or dry
in a dryer. DO NOT dry clean.
Spot clean with a damp cloth
and a mild detergent. NO
BLEACH.