GE 5GE752RB3A - Manual (Page 8)

PB-31101-035A
Supersedes PB-31101-035
DRILLING MOTOR
MODEL 5GE752RB3A
SEPTEMBER 10, 1997 8
QUANT
REQ.
FIG. REF. COL.
NO. NO. PART NO. A DESCRIPTION
2 43 41D735504G6 1 SHUNT ASSEMBLY
2 44 481A539P32 2 CABLE BUSHING, 1 7/32 IN ID, RUBBER
2 45 41A216775P1 AR SEALANT, 1/8 BY 3 3/4 IN, 10 FT ROLL
2 46 N22P33028 1 BOLT, HEX HD, 5/8 IN-11, 1 3/4 IN LONG
2 47 N22P33024 1 BOLT, HEX HD, 5/8 IN-11, 1 1/2 IN LONG
2 48 N405P47B13 2 LOCKWASHER, 5/8 IN
2 49 N213P33 2 NUT, HEX, JAM, 5/8 IN-11
2 50 N22P27028B13 2 BOLT, HEX HD, 7/16 IN-14, 1 3/4 IN LONG
2 51 N405P44B13 12 LOCKWASHER, 7/16 IN
2 52 4713845P1 1 BOLTING PLATE
2 53 N22P27020B13 10 BOLT, HEX HD, 7/16 IN-14, 1 1/4 IN LONG
2 54 41A230733P4 8 BOLT W/WASHER, SL HX HD, 1/4 IN-20, 1/2 IN LONG
2 55 8809650P1 8 WASHER, CONCAVE, 1/4 IN, SPR STL
2 56 N203P21B13 8 NUT, HEX, 1/4 IN-20
2 57 41A239176P443 AR SILASTIC PUTTY
2 58 41A239176P133 AR SILICONE TAPE, 0.015 IN THICK, 1 IN WIDE
2 59 41A239176P18 AR *TAPE, MICA, 0.005 IN THK, 0.750 IN WIDE
2 60 41A231281P47 7 BRAZING STRIP
2 61 41A239176P399 AR CORD, 0.073 IN DIA, LINEN
2 62 41A210359P12 2 REDUCING BUSHING, 1 1/2 IN TO 3/4 IN
1 63 41B537963P1 12 CARBON BRUSH
1,2,3 64 41C632667G6 4 BRUSH HOLDER ASSEMBLY
3 65 41B530659G2 12 PRESSURE ARM
3 66 41A231370P2 12 BUSHING, 1.063 IN LONG
3 67 186V831P1 8 SLEEVE
3 68 41A231378P2 4 PIN, 3/8 IN DIA, 6 5/8 IN LONG
3 69 N509P2548 8 PIN, SPRING DOWEL, 1/4 IN DIA, 3 IN LONG
3 70 N509P912 8 PIN, SPRING DOWEL, 3/32 IN DIA, 3/4 IN LONG
3 71 41A230733P7 8 BOLT W/WASHERS, HEX HD SL, 5/16 IN-18, 3/4 IN LONG
3 72 41A231370P6 16 BUSHING, 0.575 IN LONG
3 73 41A330248P1 12 SPRING SEAT
3 74 41A233867G4 12 SPRING SEAT WITH PIN
3 75 41B537844G1 12 SPRING SET ASSEMBLY
3 76 41A233880P1 4 PIN, 7 7/16 IN LONG
3 77 41B535754G28 8 BRUSH HOLDER STUD, MOLDED (0.002 IN OVERSIZE)
3 78 41B535754G29 8 BRUSH HOLDER STUD, MOLDED (0.004 IN OVERSIZE)
3 79 41B535754G30 8 BRUSH HOLDER STUD, MOLDED (0.006 IN OVERSIZE)
3 80 41B535754G31 8 BRUSH HOLDER STUD, MOLDED (0.008 IN OVERSIZE)
1 81 2733755P7 4 BRUSH HOLDER SUPPORT CLAMP
1 82 N22P37052 4 BOLT, HEX HD, 7/8 IN-9, 3 1/4 IN LONG
1 83 41B537660P25 4 WASHER, FLAT, 0.968 IN ID, 1.375 IN OD
1 84 41D735773G1 1 ARMATURE ASSEMBLY
* ADDED OR CHANGED SINCE LAST ISSUE.