GE 26730 User Manual

Smith john, Id f, Id n

Advertising

NTRODUCTION

Your Caller ID phone stores and displays specific
information, provided by your local telephone company, to
subscribers of Caller ID or similar caller identification
services. You must subscribe to one of these services in
order to use this unit.

Your Caller ID phone enables you to:

• Identify callers before you answer the phone.

• View the time and date of each incoming call.

• Record up to 40 Caller ID messages sequentially.

• Know who called while you were away.

To get the most from your new phone, we suggest that you
take a few minutes right now to read through this user's
guide.

IMPORTANT:

In order to use this feature, you must

subscribe to either the standard Name/Number Caller
ID Service or Caller ID with Call Waiting Service. To
know who is calling while you are on the phone, you
must subscribe to Caller ID with Call Waiting Service.

IMPORTANT:

Because cordless phones operate on

electricity, you should have at least one phone in your
home that isn’t cordless, in case the power in your
home goes out.

EFORE

EGIN

ARTS

HECKLIST

Make sure your package includes the items shown here.

ODULAR

ACK

EQUIREMENTS

You need an RJ11 (CA11A) type modular
jack, which is the most common type of
phone jack and might look like the one
pictured here. If you don’t have a modular
jack, call your local phone company to find
out how to get one installed.

INSTALLATION NOTE:

Some cordless telephones

operate at frequencies that may cause interference to
nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone
should not be placed near or on top of a TV or VCR. If
such interference continues, move the cordless
telephone farther away from the TV or VCR.

IGITAL

ECURITY

YSTEM

Your cordless phone uses a digital security system to
provide protection against false ringing, unauthorized
access, and charges to your phone line.

When you place the handset in the base, the unit verifies
its security code. After a power outage or battery
replacement, you should place the handset in the base for
about 20 seconds to reset the code.

NSTALLATION

ESKTOP

NSTALLATION

NOTE:

For desktop charging only, the handset is able

to charge facing up or down.

1. Place the handset in the base.

2. Raise the base antenna.

3. Plug the power supply cord into an AC outlet. The

CHARGE/IN USE indicator comes on indicating that the
battery is charging.

Allow the phone to charge for 12 hours before
using the first time. If you don't charge the phone
properly (for 12 hours) when you first set up the
phone, performance of the battery will be
compromised.

4. After charging, connect the telephone line cord to the

wall jack.

5. Set the RINGER switch on the handset to ON.

NOTE :

The phone automatically defaults to touch-

tone dialing. To change to pulse (rotary) dialing, see
“Tone/Pulse Dialing”. If you don’t know which type of
service you have, check with the phone company.

ALL

OUNT

NSTALLATION

Because it is necessary to charge the handset for 12 hours
prior to connecting the phone for use the first time, it is
better to leave the unit on a flat surface during initial
charge before attempting to hang it on the wall.

1. Place the handset in the base.

2. Plug the power supply into an AC outlet.

The CHARGE/IN USE indicator comes on indicating that
the battery is charging.

Allow the phone to charge for 12 hours before
using the first time. If you don't charge the
phone properly (for 12 hours) when you first set
up the phone, performance of the battery will be
compromised.

3. Set the RINGER switch on the handset to ON.

4. After charging, plug

the telephone line
cord into the wall jack.

5. Attach the mounting

bracket by inserting
the two tabs at the top
and then snapping the
tab at the bottom into
place.

6. Slip the mounting

holes over the wall
plate posts and slide
the unit down firmly
into place. (Wall plate
not included.)

7. Raise the base

antenna.

NOTE :

The phone automatically defaults to touch-

tone dialing. To change to pulse (rotary) dialing, see
“Tone/Pulse Dialing”. If you don’t know which type of
service you have, check with the phone company.

ORDLESS

HONE

ASICS

ECEIVING

ALL

1. Check the display to see who is calling.

2. Press the TALK button.

AKING

ALL

To make a call, press the TALK button before you dial and
press it again to hang up.

EDIAL

Press the REDIAL button to redial the last number you
dialed, (up to 32 digits).

LASH

Use the FLASH button to activate custom calling services
such as call waiting or call transfer, which
are available through your local phone company.

TIP:

Don’t use the TALK button to activate custom

calling services such as call waiting, or you’ll hang up
the phone.

HANNEL

UTTON

While talking, you might need to manually change the
channel in order to get rid of static. Press and release the
CHANNEL button to advance to the next clear channel.

EMPORARY

ONE

This feature enables pulse (rotary) service phone users to
access touch-tone services offered by banks, credit card
companies, etc., by pressing the TONE button to
temporarily make the phone touch-tone compatible. To get
information about your bank account, for example, you
would:

1. Call the bank’s information line.

2. Press the TONE button (*) after your call is answered.

3. Follow the voice instructions to complete your

transaction.

4. Hang up when finished. The phone returns to pulse

(rotary) service.

INDING

THE

ANDSET

This feature helps to locate a misplaced handset.

Press the PAGE/FIND button on the base. The handset
beeps continuously for about 2 minutes or until you press
any button on the handset.

INGER

WITCH

The RINGER switch must be ON for the handset to ring
during incoming calls.

ONE

ULSE

IALING

This adjustment allows you to select tone (touch-tone) or
pulse (rotary) mode dialing. The phone is automatically set
for touch-tone use.

ONE

1. Make sure the phone is OFF.

2. Press and hold the CHANNEL button for 2 seconds until

the phone beeps.

3. Press TONE*

ULSE

1. Make sure the phone is OFF.

2. Press and hold the CHANNEL button for 2 seconds until

the phone beeps.

3. Press #.

OLUME

The VOLUME button controls the volume of the handset's
earpiece.

OICE

ESSAGING

Provided your phone
company offers voice
messaging service and
you subscribe to it, the
CHARGE/IN USE
indicator on the base
flashes when the
phone is not in use to
indicate there is a
message waiting. It
stops flashing after the
message has been
reviewed.

IALING

ALLER

ID N

UMBER

1. Make sure the phone is OFF.

2. Use the arrow (* and #) buttons to display the desired

Caller ID record.

3. Press CALL BACK. The number dials automatically.

HANGING

THE

UMBER

ORMAT

The FORMAT button lets you change the format of the
displayed number. The available formats are as follows.

7-digit

7-digit telephone number.

10-digit

3-digit area code + 7-digit telephone
number.

11-digit

long distance code “1” + 3-digit area code+
7-digit telephone number.

1. Use the arrow buttons (* and #) to scroll to the number

you want to call back.

2. If the number will not dial as shown, press the FORMAT

button. Repeat if necessary, until the correct number of
digits are shown.

3. Press CALL BACK. The number dials automatically.

NOTE:

To clear the local area code, press and hold

CHANNEL until AREA CODE appears. Then enter
"000".

EMORY

Store up to ten 24-digit numbers in memory for quick
dialing. This memory feature is in addition to the 40 Caller
ID records that can be stored in the Caller ID memory log.

TORING

UMBER

EMORY

1. Make sure the phone is OFF.

2. Press the MEMORY button.

3. Press the memory location number (0-9).

4. Press MEMORY again. The display shows

ENTER NAME.

NOTE:

If you don't want to enter the name, skip step 5.

5. Use the keypad to store a name (up to 15 characters).

More than one letter or character is stored in each of the
number keys. For example, to enter Joe Smith, press 5
for J; press 6 three times for O; press 3 two times for E;
press 1 to enter a space before you start entering the
last name; press 7 four times for S; press 6 for M; press
4 three times for I; press 8 for T; and 4 two times for H.

If you're using two letters consecutively that are stored
in the same number key, you must press FORMAT
between the letters. For example, if you enter Barb,
press 2 two times for B; press FORMAT; press 2 for A; 7
three times for R; and 2 two times for B. You need to
press FORMAT between the B and the A since they are
stored within the same number key.

6. Press MEMORY. The display shows

ENTER TEL NUMBER.

7. Use the keypad to enter the number you want to store

(up to 24 digits). To add a pause, See “Inserting a Pause
in the Dialing Sequence”.

8. Press MEMORY again to store the number.

9. Record whose number is stored in the location on the

memory label provided. You will also be able to view
the name and number in the display.

WARNING:

TO PREVENT FIRE

OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

THE EXCLAMATIO
POINT WITHIN TH
T R I A N G L E I S A
WARNING SIG
ALERTING YOU O
I M P O R T A N T
I N S T R U C T I O N
A C C O M P A N Y I N
T H E P R O D U C T

T H E L I G H T N I N G
FLASH AND ARROW-
HEAD WITHIN THE
T R I A N G L E I S A
W A R N I N G

S I G N

ALERTING YOU OF
" D A N G E R O U S
VOLTAGE" INSIDE
THE PRODUCT.

CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
D O N O T R E M O V E C O V E R
( O R B A C K ) . N O U S E R -
S E R V I C E A B L E PA R T S I N -
S I D E . R E F E R S E R V I C I N G
T O Q U A L I F I E D S E R V I C E
PERSONNEL.

Base

Handset

PA G E /
F I N D

CHARGE/
IN USE

Mounting bracket

ABC

DEF

JKL

GHI

MNO

PQRS

WXYZ

TUV

TONE

OPER

PHONE

TALK

REDIAL

CALL BACK

VOLUME

DELETE

CHANNEL FORMAT MEMORY FLASH

OFF

RINGER

Time

Date

Caller ID name

Number of calls

Caller ID phone number

3175554231

10:51

A.M.

8/11

REPT

CALL

NEW

MEMO

SMITH JOHN

PA G E /
F I N D

CHARGE/
IN USE

CHARGE/IN USE indicator

26730

25-Channel Caller ID with Call
Waiting Cordless Telephone
User's Guide

We bring good things to life.

MPORTANT

NFORMATION

NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operational and safety requirements. The Industry Canada
does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to
be connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.

Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe systems, if present, are connected together. This precaution may be
particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or electrician,
as appropriate.

NOTES: This equipment may not be used on coin service provided by the
telephone company.

Party lines are subject to telephone company tariffs and, therefore, you may
not be able to use your own telephone equipment if you are on a party line.

Check with your local telephone company.

NTERFERENCE

NFORMATION

This equipment generates and uses radio frequency energy which may
interfere with residential radio and television reception if not properly
installed and used in accordance with instructions contained in this manual.
Reasonable protection against such interference is ensured, although there is
no guarantee this will not occur in a given installation. If interference is
suspected and verified by switching this equipment on and off, the user is
encouraged to try to correct the interference by one or more of the following
measures: Reorient the radio/television receiver’s antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into
separate circuit outlets. The user may also wish to consult a qualified radio/
television technician for additional suggestions. This equipment has been
fully tested and complies with all limits for Class B computing devices
pursuant to part 15 FCC Rules and Regulations. This device complies with
RSS-210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may cause
undesired operation of the device.

Model 26730D
15575670 (Rev. 1 CAN E)
00-33
Printed in China

ABC

DEF

JKL

GHI

MNO

PQRS

WXYZ

TUV

TONE

OPER

PHONE

TALK

REDIAL

CALL BACK

VOLUME

DELETE

CHANNEL FORMAT MEMORY FLASH

OFF

RINGER

CHANNEL
button

FLASH
button

TALK
button

REDIAL
button

TONE
button

RINGER
switch

VOLUME
button

DELETE
button

CALL
BACK
button

FORMAT
button

MEMORY
button

ATLINKS Communications Canada, Inc.

(An Alcatel/Thomson Multimedia Joint Venture)

Trademark(s) ® Registered

Marque(s) ® déposée(s)

ALLER

ID F

EATURES

This unit receives and displays information transmitted by
your local phone company. This information can include
the phone number, date, and time;

or the name, phone

number, date, and time. The unit can store up to 40 calls
for later review.

ALLER

WITH

ALL

AITING

Provided you subscribe to Caller ID with Call Waiting
service from your phone company, you are able to see who
is calling when you hear the call waiting beep. The caller
identification information appears in the display after you
hear the tone.

• Press the FLASH button to put the current person on

hold so that you can answer the incoming call.

IMPORTANT:

In order to use this feature, you must

ECEIVING

AND

TORING

ALLS

When you receive a call, the information is transmitted by
the phone company to your Caller ID telephone between
the first and second ring.

When the memory is full, a new call automatically replaces
the oldest call in memory.

NEW appears in the display for

calls received that have not been reviewed.

NOTE:

Check with your local phone company

regarding name service availability.

EVIEWING

ESSAGES

As calls are received and stored, the display is updated to
let you know how many calls have been received.

• Press the arrow down (*) button to scroll through the

call records from the most recent to the oldest.

• Press the arrow up (#) button to scroll through the call

records from the oldest to the newest.

ELETING

ECORDS

Use the DELETE button to erase the record currently
shown in the display or all records.

ELETING

THE

URRENT

ECORD

1. Make sure the phone is OFF.

2. Press DELETE. The display shows

ERASE CALL ID?

3. Press DELETE again to erase the record.

ELETING

ECORDS

1. Make sure the phone is OFF.

2. Press and hold DELETE. The display shows

ERASE ALL?

3. Press DELETE again to erase all records.

Advertising

Popular Brands

Popular manuals