GE 26730 - Manual (Page 2)

C
HANGING A
S
TORED
N
UMBER
Use the same procedure to change a stored number as
you do to store a number—you’re just replacing the phone
number with a different one.
D
IALING A
S
TORED
N
UMBER
1. Make sure the phone is ON by pressing the TALK
button.
2. Press MEMORY.
3. Press the number (0-9) for the desired memory location.
The number dials automatically.
OR
1. Make sure the phone is OFF.
2. Press MEMORY.
3. Use the arrow buttons (* and #) to scroll through the
numbers stored in memory until the desired number is
shown.
4. Press CALL BACK. The number dials automatically.
IMPORTANT: If you make test calls to emergency
numbers stored in memory, remain on the line and
briefly explain the reason for the call to the dispatcher.
Also, it’s a good idea to make these calls in off-peak
hours, such as early morning or late evening.
I
NSERTING A
P
AUSE IN THE
D
IALING
S
EQUENCE
Press the REDIAL button to insert a delay in the dialing
sequence of a stored telephone number when a pause is
needed to wait for a dial tone (for example after you dial 9
for an outside line, or to wait for a computer access tone).
Each pause counts as 1 digit in the dialing sequence.
R
EVIEWING AND
D
ELETING
S
TORED
N
UMBERS
1. Press MEMORY, then press the arrow (* and #) keys to
view the entry.
2. While the entry is displayed, press DELETE to delete the
entry. The display shows ERASE MEMO?
3. Press DELETE a second time to delete the entry.
C
HAIN
D
IALING FROM
M
EMORY
Use this feature to make calls which require a sequence of
numbers such as using a calling card for a frequently
called long distance number. Basically, you dial each part
of the sequence from memory. The following example
shows how you can use chain dialing to make a call
through a long distance service:
The Number For Memory Location
Long distance access number 7
Authorization code 8
Frequently called long distance number 9
1. Make sure the phone is ON.
2. Press MEMORY and then press 7.
3. When you hear the access tone, press MEMORY and
then press 8.
4. At the next access tone, press MEMORY and then 9.
TIP: Wait for the access tones before pressing the next
memory button, or your call might not go through.
B
ATTERY
S
AFETY
P
RECAUTIONS
• Do not burn, disassemble, mutilate, or puncture. Like
other batteries of this type, toxic materials could be
released which can cause injury.
• To reduce the risk of fire or personal injury, use only the
battery listed in the User’s Guide.
• Keep batteries out of the reach of
children.
• Remove batteries if storing over 30
days.
C
HANGING THE
B
ATTERY
Make sure the telephone is OFF
before you replace battery.
1. Remove the battery compartment
door.
2. Disconnect the cord attached to the
battery pack and remove the
battery pack from the handset.
3. Insert the new battery pack and
connect the cord into the jack inside
the handset.
4. Put the battery compartment door back on.
5. Place handset in the base to charge. If you don’t charge the
handset battery properly (for 12 hours) when you first set up the
phone and/or when you install a new battery pack, the battery’s
long-term performance will be compromised.
T
ELEPHONE
N
ETWORK
I
NFORMATION
Should your equipment cause trouble on your line which
may harm the telephone network, the telephone company,
where practicable, may notify you that temporary
discontinuance of service may be required. Where prior
notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily
discontinue service immediately.
The telephone company may make changes in its
communications facilities, equipment, operations or
procedures where such action is required in the operation
of its business. If these changes are expected to affect the
use or performance of your telephone equipment, the
telephone company will likely give you adequate notice to
allow you to maintain uninterrupted service.
Notice must be given to the telephone company upon
termination of your telephone from your line.
REN N
UMBER
On the bottom of this equipment is a label indicating,
among other information, the FCC Registration number
and Ringer Equivalence Number (REN) for the equipment.
You must, upon request, provide this information to your
telephone company.
The REN is useful in determining the number of devices
you may connect to your telephone line and still have all
of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of
all devices connected to one line should not exceed 5. To
be certain of the number of devices you may connect to
your line as determined by the REN, you should contact
your local telephone company.
M
ESSAGE
I
NDICATORS
The following indicators show the status of a
message or of the unit.
ERROR Caller information has been interrupted
during transmission or the phone is
excessively noisy.
ENTER NAME Prompt telling you to enter a name for
one of the 10 memory locations.
ERASE ALL? Prompt asking if you want to erase all
Caller ID records.
ERASE CALL ID? Prompt asking if you want to erase the
current Caller ID record that is shown
on the display.
ERASE MEMO? Prompt asking if you want to erase one
of the 10 numbers stored in the
phone's outgoing memory.
END OF LIST Indicates there is no additional
information in the Caller ID memory
log.
NEW Indicates call or calls have not been
reviewed.
UNKNOWN The incoming call is from an area not
serviced by Caller ID or the information
was not sent.
PAGING YOU Someone has pressed the PAGE button
on the base.
BLOCKED The person is calling from a number
that has been blocked from
transmission.
REPT Repeat call message. Indicates that a
new call from the same number was
received more than once.
NO DATA No Caller ID information was received.
H
ANDSET
S
OUND
S
IGNALS
Signal Meaning
A long warbling tone Signals an incoming call
(with ringer on)
One short beep, one Page signal
long beep (several times)
Three short beeps Out of range
Four short beeps Low battery warning
T
ROUBLESHOOTING
T
IPS
C
ALLER
ID
Problem Solution
No Display • Is battery fully charged?
Try replacing the battery.
• If you are using AC power,
make sure that the unit is
connected to a non-
switched electrical outlet.
Disconnect the unit from
the plug and plug it in
again.
• Did you order Caller ID
service from your local
telephone company?
Caller ID Error Message • The unit displays this
message if it detects
anything other than valid
Caller ID information
during the silent period
after the first ring. This
message indicates the
presence of noise on the
line.
T
ELEPHONE
Problem Solution
No dial tone • Check installation:
— Is the base power cord
connected to a working
outlet?
— Is the telephone line cord
connected to the base unit
and the wall jack?
• Disconnect the base from
the wall jack and connect
another phone to the same
jack. If there is no dial tone
in the second phone, the
problem might be your
wiring or local service.
• Is the handset out of range
of the base?
• Make sure the battery is
properly charged (12
hours).
• Is the battery pack
installed correctly?
• Did the handset beep
when you pressed the
TALK button? Did the
CHARGE/ IN USE indicator
come on? The battery may
need to be charged.
T
ELEPHONE
Problem Solution
Dial tone is OK, but • Make sure the tone/pulse
can't dial out setting is programmed
correctly.
Handset does not ring • Make sure the RINGER
switch on the handset is
turned to ON.
• You may have too many
extension phones on your
line. Try unplugging some
phones.
• See solutions for “No dial
tone.”
You experience static, • Change channels
noise, or fading in • Is handset out of range?
and out Move closer to the base.
• Does the base need to be
relocated?
• Charge battery.
• Make sure base is not
plugged into an outlet with
another household
appliance.
Unit beeps • Place handset in base for
20 seconds to reset the
security code. If that
doesn’t work, charge
battery for 12 hours.
• Clean charging contacts on
handset and base with a
soft cloth, or an eraser.
• See solutions for “No dial
tone.”
• Replace battery.
Memory Dialing • Did you program the
memory location keys
correctly?
• Did you follow proper
dialing sequence?
• Make sure the tone/pulse
setting is programmed
correctly.
• Did you reprogram
numbers into memory
after power outage or
battery replacement?
NOTE: This product contains a nickel-
cadmium rechargeable battery and must
be recycled or disposed of properly. We
suggest that you check with your local
Environmental Agency regarding
recycling or disposal.
G
ENERAL
P
RODUCT
C
ARE
To keep your telephone working and looking good, follow
these guidelines:
• Avoid putting the phone near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping the handset, as well as other rough
treatment to the phone.
• Clean the phone with a soft cloth.
• Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
• Retain the original packaging in case you need to ship
the phone at a later date.
• Periodically clean the charge contacts on the handset
and base with a clean pencil eraser.
C
AUSES OF
P
OOR
R
ECEPTION
• Aluminum siding
• Foil backing on insulation
• Heating ducts and other metal construction can shield
radio signals
• You’re too close to appliances such as microwaves,
stoves,
computers, etc.
• Atmospheric conditions, such as strong storms
• Base is installed in the basement or lower floor of the
house
• Base is plugged into an AC outlet with other electronic
devices
• Baby monitor is using the same frequency
• Handset battery is low.
• You’re out of range of the base.
S
ERVICE
ATLINKS Communications Canada, Inc., warrants to
the purchaser or gift recipient that if any manufac-
turing defect becomes apparent in this product
within
1 year from the original date of purchase, it will be
replaced free of charge, including return
transportation.
This warranty does not include damage to the
product resulting from accidents, misuse or leaking
batteries.
Should your product not perform properly during
the warranty period, either:
1. Return it to the selling dealer with proof of
purchase for replacement,
OR
2. Remove the batteries (where applicable), and pack
product complete with accessories in the original
carton (or equivalent).
— Mail prepaid (with proof of purchase) and
insured to:
ATLINKS Communications Canada, Inc.
c/o Thomson Consumer Electronics Canada,Inc.
6200 Edwards Boulevard
Mississauga, Ontario
Canada L5T 2V7
The provisions of this written warranty are in
addition to and not a modification of or subtraction
from the statutory warranties and other rights and
remedies contained in any applicable legislation,
and to the extent that any such provisions purport to
disclaim, exclude or limit any such statutory
warranties and other rights and remedies, such
provisions shall be deemed to be amended to the
extent necessary to comply therewith.
If you are unable to find a qualified servicer for out
of warranty service, you may write to:
ATLINKS Communications Canada, Inc.
c/o Thomson Consumer Electronics Canada, Inc.
P.O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future
reference. This information is required if service is
needed during the warranty period.
PURCHASE DATE
____________________________________________________________
NAME OF STORE
____________________________________________________________
DESCRIPTION
A
CCESSORY
O
RDER
F
ORM
Replacement
handset battery
CAT NUMBER TOTAL QUANTITY PRICE*
BT-12
CUSTOMER: CUT ALONG DOTTED LINE.
✂
$9.95
Ni-Cd
Must be Recycled or
Disposed of Properly
Contains
Nickel-Cadmium
Rechargeable Battery
Please make sure that this form has been filled out completely.
*Prices are subject to change without notice.
Total Merchandise.........................................$_______________
Sales Tax........................................................$_______________
We are required by law to collect the appropriate sales tax for each individual state,
county, and locality to which the merchandise is being sent. Duties will apply for
shipments to Canada.
Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.
currency only. No COD or Cash. All accessories are subject to availability. Where
applicable, we will ship a superseding model.
Shipping/Handling........................................ $_______________
Total Amount Enclosed.................................$_______________
Mail order form and money order or check (in U.S. currency)
made payable to Thomson Consumer Electronics, Inc. to:
TCE
Mail Order Department
P.O. Box 8419
Ronks, PA 17573-8419
Name_______________________________________________________
Address_____________________________________ Apt.____________
City ________________________State________ ZIP_________________
Daytime Phone Number ( )_______________________________
$5.00
____________________________________________________________________
Authorized Signature
My card expires:
Copy the number above your
name on the Master Card
For credit card purchases
Your complete charge card number, its expiration date and your
signature are necessary to process all charge card orders.
Copy your complete account number from your VISA card.
My card expires:
Copy your complete account number from your
Master Card or Discover.
To order, call 1-800-338-0376 (for accessories only) or
complete this order form.