GE 26920R - Manual

D
ESKTOP
I
NSTALLATION
1. Make sure the mounting bracket is securely fastened to the bottom of the base. The
mounting bracket should be snapped into the upper four slots on the base’s bottom.
2. Set the RINGER switch (on the handset) to ON, and place handset in the cradle on
the base.
3. Plug the power supply into an AC outlet. The CHARGE/IN USE indicator comes on
and indicates the battery is charging.
Allow the phone to charge for 12 hours prior to first use. If you don’t properly charge
the phone, battery performance will be compromised.
4. Plug the telephone line cord into a modular phone jack.
5. Raise the base antenna.
NOTE: The phone automatically defaults to touch-tone dialing. To change to pulse
(rotary) dialing, see “Tone/Pulse Dialing.” If you don’t know which type of service you
have, check with the phone company.
4. Plug the telephone line cord into a modular phone jack.
5. Remove the handset hook; turn it upside down, and put it back in the slot (you need
to do this to keep the handset from falling out of the base).
6. Slip the mounting holes (on the bottom of the base and on the bracket) over the wall
plate posts and slide the unit down firmly into place. (Wall plate not included.)
7. Raise the base antenna.
NOTE: The phone automatically defaults to touch-tone dialing. To change to pulse
(rotary) dialing, see “Tone/Pulse Dialing.” If you don’t know which type of service you
have, check with the phone company.
C
ORDLESS
P
HONE
B
ASICS
M
AKING A
C
ALL
After initial set up, put handset in the base for 12 hours to
charge the battery.
The only two things you need to know to make a call are:
• Press the TALK button before you dial.
• Press TALK or place the handset in the base to hang up.
I
N
U
SE
I
NDICATOR
You know the phone is on when you see the IN USE
indicator on the handset light.
R
EDIAL
Press the TALK button, then press the RE/PA (redial/pause)
button to redial the last number you called (up to 32 digits).
R
ECEIVING A
C
ALL
To answer a call, you must press the TALK button before you
can talk.
F
LASH
Use the FLASH button to activate custom calling services
such as Call Waiting or call transfer, which are available
through your local phone company.
TIP: If you press the TALK button to activate custom
calling services such as call waiting, you’ll hang up the
phone. Press FLASH instead.
V
OLUME
The VOL button controls the volume of the handset's
earpiece.
R
INGER
S
WITCH
The handset ringer switch can be set to ON or OFF. If the switch is off, the unit will not ring.
26920/26921
40-Channel 900MHz
Cordless Telephone
User’s Guide
FCC R EGISTRATION I NFORMATION
Your telephone equipment is registered with the Federal Communications Commission and is in compliance with parts 15 and
68, FCC Rules and Regulations.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and Ringer
Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone
company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these
devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices
connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
Notes
•
This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you
are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall,
where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not
practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service
immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a
complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of procedures where
such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these
changes are expected to affect the use or performance of your telephone equipment, the telephone company must give
you adequate notice, in writing, to allow you to maintain uninterrupted service.
I NTERFERENCE I NFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference; and (2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician
for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C.
20402. Please specify stock number 004-000-00345-4 when ordering copies.
H EARING A ID C OMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatibility.
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
ATLINKS USA, Inc.
10330 North Meridian Street
Indianapolis, IN 46290
© 2001 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
We bring good things to life.
I
NTRODUCTION
Your 900 MHz Cordless Telephone is designed to give you flexibility in use and high
quality performance. To get the most from your new cordless telephone, we suggest
that you take a few minutes right now to read through this instruction manual.
Headset (for
26921 only) Belt Clip (for
26921 only)
Handset Base
Mounting
bracket
CHARGE/
IN USE
PAGE
CHAN
MNO 6 JKL 5 GHI 4
DEF 3 ABC 2 1
WXYZ 9 TUV 8 PQRS 7
# OPER 0 TONE *
TALK
MUTE FLASH RE/PA
MEM ON OFF VOL RINGER
M
ODULAR
J
ACK
R
EQUIREMENTS
You need an RJ11 type modular jack, which is the most common type of phone
jack and might look like the one pictured here. If you don’t have a modular jack,
call your local phone company to find out how to get one installed.
D
IGITAL
S
ECURITY
S
YSTEM
Your cordless phone uses a digital security system to provide protection against false
ringing, unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security code. After a
power outage or battery replacement, you should place the handset in the base for
about 20 seconds to reset the code.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that may
cause interference to nearby TVs and VCRs. To minimize or prevent such interference,
the base of the cordless telephone should not be placed near or on top of a TV or VCR.
If interference continues, moving the cordless telephone farther away from the TV or
VCR will often reduce or eliminate the interference.
I
NSTALLATION
W
ALL
M
OUNT
I
NSTALLATION
Because it is necessary to charge the handset
for 12 hours prior to connecting the phone for
use the first time, it is better to leave the unit on
a flat surface during initial charge before
attempting to hang it on the wall.
1. Set the RINGER switch (on the handset) to
ON, and place the handset in the cradle on
the base.
2. Plug the power supply into an AC outlet. The
CHARGE/IN USE indicator comes on and
indicates the battery is charging.
Allow the phone to charge for 12 hours prior
to first use. If you don’t properly charge the
phone, battery performance will be
compromised.
3. Turn the phone over and remove the
mounting bracket by pressing the tabs at the
top of the bracket. Turn the bracket upside
down and reattach it to the base by inserting
the tabs into the lower four slots on the
bottom of the unit.
M
UTE
Use the MUTE button to interrupt a phone conversation to talk privately with someone
else in the room.
1. Press MUTE to activate mute feature (the BAT LOW/MUTE indicator blinks).
2. Press MUTE again to turn it off.
T
ONE
/P
ULSE
D
IALING
This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing.
The phone is automatically set for touch-tone use.
T
ONE
1. Make sure the phone is OFF.
2. Press and hold the CHAN button for 2 seconds until the phone beeps.
3. Press TONE*.
P
ULSE
1. Make sure the phone is OFF.
2. Press and hold the CHAN button for 2 seconds until the phone beeps.
3. Press #.
T
EMPORARY
T
ONE
This feature enables pulse (rotary) service phone users to access touch-tone services
offered by banks, credit card companies, etc., by pressing the TONE button to
temporarily make the phone touch-tone compatible. To get information about your bank
account, for example, you would:
1. Press the TALK button.
2. Call the bank’s information line.
3. Press the TONE button after your call is answered.
4. Follow the voice instructions to complete your transaction.
5. Hang up when finished. The phone returns to pulse (rotary) service.
P
AGING THE
H
ANDSET
Press the PAGE button on the base to locate a
misplaced handset. When you press the PAGE
button, the handset beeps. Press the TALK button
when you locate the handset.
NOTE: You can still page the handset with the
ringer off.
C
HANNEL
B
UTTON
If you ever experience any interference or don’t have clear voice quality, press the
CHAN button on the handset to advance to another channel.
M
EMORY
Store up to 10 numbers in memory for quick dialing.
S
TORING A
N
UMBER IN
M
EMORY
1. Make sure the phone is OFF.
2. Press the MEM button.
3. Dial the number (up to 20 digits).
4. Press MEM.
5. Press any number key (0-9) to store the phone number
in that memory location.
C
HANGING A
S
TORED
N
UMBER
Use the same procedure to change a stored number as
you do to store a number— you’re just replacing the
phone number with a different number.
S
TORING A REDIAL NUMBER
1. Make sure the phone is OFF.
2. Press MEM.
3. Press RE/PA.
4. Press MEM.
5. Press any number key (0-9) to store the phone number in that memory location.
Model 26920R
15726700 (Rev. 2 E/S)
01-05
Printed in China
CHAN
MNO 6 JKL 5 GHI 4
DEF 3 ABC 2 1
WXYZ 9 TUV 8 PQRS 7
# OPER 0 TONE *
TALK
MUTE FLASH RE/PA
MEM
ON OFF
VOL
RINGER
MEM button
CHAN button
RE/PA
button
CUS
T
OMER:
CUT
AL
ONG DO
T
TED LINE.
✂
DESCRIPTION
CATALOG NUMBER
PRICE* QUANTITY TOTAL
Belt clip 5-2452 $5.95
Headset 5-2425 $36.35
5-2459 $13.10 Replacement battery
5-2451
5-2444
(white) (black)
IMPORTANT: Because cordless phones operate on electricity, you should have at least one
phone in your home that is not cordless, in case the power in your home goes out.
B
EFORE
Y
OU
B
EGIN
P
ARTS
C
HECKLIST
Make sure your package includes the items shown here.
4
2
1
3
5
CHARGE/
IN USE
PAGE
PAGE
button
CHAN
MNO 6 JKL 5 GHI 4
DEF 3 ABC 2 1
WXYZ 9 TUV 8 PQRS 7
# OPER 0 TONE *
TALK
MUTE FLASH RE/PA
MEM
ON OFF
VOL
RINGER
RE/PA
button
TALK
button
CHAN
MNO 6 JKL 5 GHI 4
DEF 3 ABC 2 1
WXYZ 9 TUV 8 PQRS 7
# OPER 0 TONE *
TALK
MUTE FLASH RE/PA
MEM
ON OFF
VOL
RINGER
FLASH
button MUTE
button
RINGER– ON
OFF switch VOL button
S
TORING A
P
AUSE IN
M
EMORY
Use the RE/PA button to insert a pause when a delay is needed in the dialing sequence
(for example, when you must dial a 9 to get an outside line or when you must enter
codes to access your bank’s information line). Each pause counts toward the 20-digit
limit.
If you need to dial 9 to get an outside line and want to store a number in memory
without having to dial 9 each time, you would:
1. Make sure the phone is OFF.
2. Press MEM.
3. Press 9.
4. Press RE/PA.
5. Dial the phone number you want to store in memory.
6. Press MEM.
7. Press any number key (0-9) to store the phone number in that memory location.
TIP: If you need a longer pause, press RE/PA button more times.
D
IALING A
S
TORED
N
UMBER
1. Make sure the phone is ON by pressing the TALK button.
2. Press MEM.
3. Press the number (0-9) for the desired memory location. The number dials
automatically.
IMPORTANT: If you make test calls to emergency numbers stored in memory, remain
on the line and briefly explain the reason for the call to the dispatcher. Also, it’s a good
idea to make these calls in off-peak hours, such as early morning or late evening.
H
EADSET AND
B
ELT
C
LIP
O
PERATION
C
ONNECTING A
HEADSET TO THE
HANDSET
For hands free conversation, connect the
headset (provided with 26921 only) to the
HEADSET jack as shown. The handset
receiver and microphone are disabled
when the headset is connected.
Adjust the headset to rest comfortably on
top of your head and over your ear. Move
the microphone to approximately 2 to 3
inches from your mouth.
• Press the TALK button to answer or
place a call before using the
headset.
C
ONNECTING THE
B
ELT
C
LIP
There are two slots, one on each side of
the handset.
• Attach the belt clip (provided with
26921 only) by inserting the sides of
the belt clip into the slots. Snap the
ends of the belt clip into place.
C
HANGING THE
B
ATTERY
Make sure the telephone is OFF before you replace battery.
1. Remove the battery compartment door.
2. Disconnect the cord attached to the battery pack and
remove the battery pack from the handset.
3. Insert the new battery pack and connect the cord into the
jack inside the handset.
4. Put the battery compartment door back on.
5. Place handset in the base to charge. If you don’t charge
the handset battery properly (for 12 hours) when you first
set up the phone and/or when you install a new battery
pack, the battery’s long-term performance will be
compromised.
B
ATTERY
S
AFETY
P
RECAUTIONS
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type,
toxic materials could be released which can cause injury.
• To reduce the risk of fire or personal injury, use only the battery listed in the User’s
Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
HE
AD
S E T
HEADSET
jack
Headset plug
Slot for
belt clip Slot for
belt clip
NOTE: The RBRC seal on the battery used in your ATLINKS
USA product indicates that we are participating in a program
to collect and recycle Nickel Cadmium batteries throughout
the United States. Please call 1-800-8-BATTERY for
information or contact your local recycling center.
T
ROUBLESHOOTING
G
UIDE
In case of difficulty, please check the following Troubleshooting Guide before seeking
service.
Problem Solution
No dial tone • Check installation:
— Is the base power cord connected to a
working outlet?
— Is CHARGE/IN USE indicator on?
— Is the telephone line cord connected to
the base unit and the wall jack?
• Disconnect the base from the wall jack
and connect another phone to the same
jack. If there is no dial tone in the second
phone, the problem might be your wiring
or local service.
• Is the handset out of the base unit’s
range? Move closer to the base unit.
• Make sure the battery is properly charged
(12 hours).
• Is the battery pack installed correctly?
• If the phone still does not work, discon-
nect the power cord and remove the
battery pack. Then reconnect the power
cord and reinstall the battery pack. Place
handset in the base for 10 seconds to
allow it to reinitialize.
Dial tone is OK, but • Make sure the tone/pulse setting is
can’t dial out programmed correctly.
Handset does not ring • Make sure the RINGER switch on the
handset is turned to ON.
• You may have too many extension phones
on your line. Try unplugging some
phones.
• See solutions for “No dial tone.”
Cannot hear phone • Press the VOL button to adjust the
conversation volume to the desired listening level.
You experience static, • Change channels.
noise, or fading in and out • Is handset out of range? Move closer to
the base.
• Does the base need to be relocated?
• Charge handset battery.
• Make sure base is not plugged into an
outlet with another household appliance.
Range is shorter • Press the CHAN button during the
than normal conversation to select a new channel.
• Position the base antenna upward.
Battery will not hold a • Be sure you are sufficiently charging the
charge or is fully charged battery. When the battery has been
and the BAT LOW lights charged for 12 hours, you can expect
approximately 4 hours of talk time.
• Check to be sure battery contacts on both
the handset and the base are making
contact and are clean; free of dirt or lint.
• When the handset is placed in the base,
check that the base CHARGE/IN USE
indicator is on.
Problem Solution
BAT LOW indicator • Place handset in base for 10 seconds to
stays on reset the phone. If that doesn’t work,
charge battery for 12 hours.
Memory Dialing • Did you program the memory location keys
doesn’t work correctly?
• Did you follow proper dialing sequence?
• Make sure the tone/pulse setting is
programmed correctly.
Unit locks up and • If the phone still does not work,
no communication disconnect the power cord and remove
between the base the battery pack. Then reconnect the
and the handset power cord and reinstall the battery pack.
Place handset in the base for 10 seconds
to allow it to reinitialize.
• If a power outage occurs while the
handset is away from the base, the
handset must be returned to the base
when the power returns.
L
IMITED
W
ARRANTY
What your warranty covers:
• Any defect in materials or workmanship.
For how long after your purchase:
• One year.
(The warranty period for rental units begins with the first rental or 45 days from date
of shipment to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit.
• The exchange unit is under warranty for the remainder of the original product’s
warranty period.
How to make a warranty claim:
• Properly pack your unit. Include any cables, etc., which were originally provided
with the product. We recommend using the original carton and packing materials.
• Include evidence of purchase date such as the bill of sale. Also print your name and
address and a description of the defect. Send via standard UPS or its equivalent to:
Thomson multimedia Inc.
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service not covered by the
warranty.
• Insure your shipment for loss or damage. Thomson accepts no liability in case of
damage or loss en route to Thomson.
• A new or refurbished unit will be shipped to you freight prepaid.
What your warranty
does not cover:
• Customer instruction. (Your Owner’s Manual provides information regarding
operating instructions and user controls. For additional information, ask your
dealer.)
• Installation and set-up service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
How state law relates to this warranty:
• This warranty gives you specific legal rights, and you may have other rights which
vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
S
ERVICE
The FCC requires this product to be serviced only by the manufacturer or its authorized
service agents. In accordance with FCC requirements, changes or modifications not
expressly approved by ATLINKS USA could void the user’s authority to operate this
product. For instructions on how to obtain service, refer to the warranty included in this
Guide or call Consumer Information, 1-800-448-0329.
Or refer inquiries to:
ATLINKS USA Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot down the date this
product was purchased or received as a gift. This information will be valuable if service
should be required during the warranty period.
Purchase date _________________Name of store____________________________
A
CCESSORY
O
RDER
F
ORM
To order, call 1-800-338-0376 (for accessories only) or complete this
order form.
My card expires:
Copy the number above your name on
the Master Card
For credit card purchases
Your complete charge card number, its expiration date and your signature
are necessary to process all charge card orders.
Copy your complete account number from your VISA card.
My card expires:
*Prices are subject to change without notice.
Total Merchandise.........................................$_______________
Sales Tax........................................................$_______________
We are required by law to collect the appropriate sales tax for each individual state,
county, and locality to which the merchandise is being sent. Duties will apply for
shipments to Canada.
Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.
currency only. No COD or Cash. All accessories are subject to availability. Where
applicable, we will ship a superseding model.
Shipping/Handling....................................... $_______________
Total Amount Enclosed.................................$_______________
Mail order form and money order or check (in U.S. currency) made payable
to Thomson multimedia Inc. to:
Thomson multimedia Inc.
Mail Order Department
P.O. Box 8419
Ronks, PA 17573-8419
Name_______________________________________________________
Address_____________________________________ Apt.____________
City ________________________State________ ZIP_________________
Daytime Phone Number ( )_______________________________
$5.00
Please make sure that this form has been filled out completely.
5
3
2
4
6
7
1
CHAN
MNO 6 JKL 5 GHI 4
DEF 3 ABC 2 1
WXYZ 9 TUV 8 PQRS 7
# OPER 0 TONE *
TALK
MUTE FLASH RE/PA
MEM
ON OFF
VOL
RINGER