Optional accessories, Dvb4136 direct vent gas fireplace, Fan kits fk12 fan assembly – Majestic Appliances DVB4136 User Manual

Page 48: Fk24 fan assembly, Hard (direct) wire hook up

Advertising
background image

48

DVB4136 Direct Vent Gas Fireplace

20012322

Optional Accessories

Fan Kits

FK12 Fan Assembly

1. Open louvre assembly bottom.
2. Install FK12 fan in back of unit between hearth sup-

ports. (Fig. 77)

3. Secure fan on velcro strips.
4. Power to the fan can be supplied by plugging the

supply lead into a conveniently located wall socket
or by using a hard-wired EB-1 connector box.

5. Be sure fan motor does not touch hearth supports.

FP1004

Fan placement

DV360/580 Series

1/25/00 djt

Cold Air Box

Side View

Front of
Unit

Hearth Pan

Base Pan

FK12 Fan

FP1004

Fig. 77 FK12 Fan Kit placement.

FK24 Fan Assembly

Fan specifications: 120 volt, 60 Hz, .75 Amp.
This fan does not need regular maintenance, however
periodic cleaning is required. Check the area under the
control door and in front of the fan and wipe or vacuum
at least once a month during the operating season.
Should this fan require servicing, the power supply must
be disconnected.
The FK24 comes with the electrical cord attached.
1. Slide fan assembly from the left side into the fire-

place opening, line up mounting holes with screw
studs on back of fireplace and fasten with #10 - 24
hex nuts. (Fig. 78)

2. Install thermal sensor on bottom of firebox using #10

- 24 hex nuts.

3. (Option A) - Place electronic fan speed control box

on bottom of fireplace base, lining up mounting holes
with screw studs. Fasten fan speed control box with
#10 - 24 hex nuts.

(Option B) - The speed control can be installed in an

electrical box at normal wall switch height for conve-
nient access.

4. The power supply may be connected in 2 ways:

Method A
Route the 6’ (1.8m) lead fitted to the unit to a conve-

niently located wall socket.

Method B
If the EB-1 receptacle box (Pt. #ZA1200) was cor-

rectly connected when the unit was installed, the
fan lead can be directly plugged into the EB-1 plug
socket.

5. Whether wiring directly to the fan junction box (Op-

tion A) or into the EB1 (electrical box, Option B) first
ensure cable is secured using box connector.

The fireplace, when installed must be elec-
trically connected and grounded in accor-
dance with local codes, with the current
CSA C22.1 Canadian Electrical Code or for
US installations, follow local codes and
the National Electrical Code, ANSI/NFPA
No. 70.

Hard (Direct) Wire Hook Up

First connect ground wire to ground stud located on
the base of either box. Black wire from supply should
connect to the variable speed switch. Alternate speed
switch wire connects to temperature sensor. Alternate
lead from sensor connects to fan. Alternate fan lead
connects back to the white supply wire. (Fig. 79)

Any electrical rewiring of this fan must be
completed by a qualified electrician.
Turn off all power before hook up.

��

���

���

��

��

��

���

����

�������

�����

����

��

��

���

���

��

��

���

�������

�����

���

TP

TH

FP1811

FK24

fan placement

7/07 djt

Electrical Box

Heat Sensor

Fan

Fan Speed

Switch

Gas Line

Valve

FP1811

Fig. 78 FK24 fan placement.

Black

White

Ground

FP394

WIRING DIAGRAM

11/20/96

Fan

Temperature

Sensor

Speed

Control

FP1025

Fig. 79 FK24 fan wiring.

Advertising