MACKIE 1402-VLZPRO - Manual (Page 16)

16
L
MONO
L
MONO
L
MONO
L
MONO
LINE IN 7–8
R R R R
LINE IN 9–10 LINE IN 11–12 LINE IN 13–14
BAL
OR
UNBAL
BAL
OR
UNBAL
BAL
OR
UNBAL
BAL
OR
UNBAL
LINE IN 3 LINE IN 4
L
R
1
2
1
2
RIGHT
AUX SEND STEREO AUX RETURN MAIN OUT
LOW CUT
75 Hz
18dB/OCT
LOW CUT
75 Hz
18dB/OCT
BAL
OR
UNBAL
BAL
OR
UNBAL
LINE IN 5
LOW CUT
75 Hz
18dB/OCT
BAL
OR
UNBAL
LINE IN 6
LOW CUT
75 Hz
18dB/OCT
BAL
OR
UNBAL
LINE IN 1 LINE IN 2
MIC 1 MIC 2 MIC 3 MIC 4 LEFT/ MONO BAL/UNBAL
LOW CUT
75 Hz
18dB/OCT
LOW CUT
75 Hz
18dB/OCT
BAL
OR
UNBAL
BAL
OR
UNBAL
ALL BAL/UNBAL MIC 5 MIC 6
TRIM TRIM TRIM TRIM TRIM TRIM
LEVEL
+4
-10 -10 -10 -10
LEVEL
+4
LEVEL
+4
LEVEL
+4
TRIM
TAPE
INPUT
TAPE
OUTPUT
L
R
MIC GAIN
+15dB -45dB
- 10dBV
0 60
MIC GAIN
+15dB -45dB
- 10dBV
0 60
MIC GAIN
+15dB -45dB
- 10dBV
0 60
MIC GAIN
+15dB -45dB
- 10dBV
0 60
MIC GAIN
+15dB -45dB
- 10dBV
0 60
MIC GAIN
+15dB -45dB
- 10dBV
0 60
XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE XDR MIC PRE
U U U U U U
ALT 3–4 OUTPUT
These 1 ⁄
4
" jacks are balanced outputs ca-
pable of delivering 22dBu into a balanced or
unbalanced load.
To learn how signals are
routed to these outputs: . To wire your own
cables: .
CONTROL ROOM
These 1 ⁄ 4 " jacks are balanced outputs ca-
pable of delivering 22dBu into a 600 ohm
balanced or unbalanced load.
To learn how
signals are routed to these outputs: . To
wire your own cables: .
AUX SEND 1&2
These 1 ⁄ 4 " jacks are also balanced outputs
capable of delivering 22dBu into a 600 ohm
balanced or unbalanced load.
To learn how
signals are routed to these outputs: . To wire
your own cables: .
PHONES
The 1402-VLZ PRO’s stereo PHONES jack
will drive any standard headphone to very loud
levels. Walkperson-type phones can also be
used with an appropriate adapter.
To learn
how signals are routed to these outputs: . If
you’re wiring your own cable for the
PHONES
output, follow standard conventions:
SLEEVE
LEFT SLEEVE
LEFT
RIGHT
RIGHT
TIP
SLEEVE RING
Tip = Left channel
Ring = Right channel
Sleeve = Common ground
WARNING: When we say
the headphone amp is
loud, we’re not kidding.
It can cause permanent
ear damage. Even inter-
mediate levels may be painfully loud with
some earphones. BE CAREFUL!
Always turn the CTL ROOM/SUBMIX fader
all the way down before connecting head-
phones. Keep it down until you’ve put the
phones on. Then turn it up slowly. Why?
“Engi-
neers who fry their ears find themselves with
short careers.”