Miller Electric KC237900 - Manual (Page 50)

9/92
OPTIONS AND ACCESSORIES
TIG-RIG ACCESSORIES
METERS FOR TIG–RIG
With 300SS Power Source
(#041 236 Factory)
(#041 237 Field)
With 400SS Power Source
(#041 238 Factory)
(#041 908 Field)
With 500SS and 600SS Power
Sources
(#041 240 Factory)
(#041 909 Field)
PC–SS PULSER
(#041 213 Field)
ELECTROSLOPE

9
(#041 212 Field)
GAS PREFLOW TIMER
(#041 404 Factory)
(#041 405 Field)
Adjustable 0.1 to 15 seconds.
SPOT WELD TIMER
(#041 407 Factory)
(#041 408 Field)
Adjustable 0.1 to 5 seconds.
REMOTE EXTENSION CABLES
(#122 973) 25 ft. (7.6 m)
(#122 974) 50 ft. (15.2 m)
For use between TIG–RIG and
power source. Can also be used to
extend FTC–14 from power source
or TIG–RIG.
AMPSET CORDLESS
REMOTE CURRENT
CONTROL
A simple cordless control that
changes welding current at any
distance from a Miller SS Series
power source. The control can be
clipped to the operator’s belt.
Before welding, the highest current
setting required is set at the power
source. To change current, the
operator replaces the welding
electrode in the holder with the
AMPSET

control and moves the
indicator on the control to the
desired higher or lower setting.
The control is then touched to the
workpiece for a few seconds and
the current is reset. Reinsert the
electrode, and weld at the new
setting.
Multiprocess capabilities – do air
carbon arc gouging at high
amperage, and weld with 1/8 in.
(3.2 mm) Stick electrode without
returning to the power source.
AMPSET can be considered
…
•
when cable–connected box–type
remote hand controls are
impractical
•
when operating a long distance
from the power source and
accurate amperages are required
•
when welding in varied positions
(flat - vertical - overhead) requiring
frequent amperage changes
•
when distance and multiprocess
usage is a dual consideration
(Stick electrode, Air Carbon Arc
Cutting and Gouging, and
touch–start TIG).
GOLD STAR SS
ACCESSORIES
REMOTE CONTROLS
RHC–14 HAND CONTROL
(#129 340)
Miniature hand control for remote
current and contactor control.
Dimensions: 4 in. (102 mm) x 4 in.
(102 mm) x 3–1/4 in. (82 mm)
Includes 20 ft. (6 m) cord and
14–pin plug.
RFC–14 FOOT CONTROL
(#129 339)
Foot current and contactor control.
Includes 20 ft. (6 m) cord and
14–pin plug.
TORCH–MOUNTED REMOTE
HAND CONTROLS
AMTV REMOTE CONTACTOR
AND CURRENT CONTROL
(#152 608)
Fastens to TIG torch handle using
two Velcro strips. The control
allows complete current and
contactor control at the operator’s
fingertips — a practical alternative
to a foot control. Includes 28 ft.
(8.5 m) control cord with 14–pin
plug.
RMLS–14
(#129 337)
Momentary– and
maintained–contact rocker switch
for contactor control. Push
forward for maintained contact and
back for momentary contact.
Includes 20 ft. (6 m) cord and
14–pin plug.
EXTENSION CABLES FOR
FTC–14
14–pin plug to 14–pin socket.
10 ft. (3 m) (#122 972)
25 ft. (7.6 m) (#122 973)
50 ft. (15.2 m) (#122 974)
75 ft. (22.8 m) (#122 975)