Marantz LN-11S1A - Manual (Page 7)

3
B
EF
O
RE
U
SE
N
A
M
E
O
F
PA
RT
S
B
A
SI
C
O
PE
RA
TI
O
N
A
D
VA
N
CE
D
O
PE
RA
TI
O
N
SE
TU
P
TR
OU
BL
ES
HO
OT
IN
G
O
TH
ER
S
B
A
SI
C
O
PE
RA
TI
O
N
BASIC OPERATION
TURNING THE POWER ON
Plug the AC cable of the AC/DC adapter into a power
outlet and plug the output plug into the DC jack of
the unit. The unit’s power turns on and the POWER
ON indicator on the top panel lights blue.
TURNING THE POWER OFF
To turn the unit’s power off, unplug the plug of the
AC/DC adapter from the DC jack. The unit’s power
turns off and the POWER ON indicator goes out.
Note:
Do not turn the unit’s power off while the anamorphic
lens is in motion. Doing so may result in damage to
equipment. If you will not be using the unit for an
extended period of time, be sure to unplug the AC/
DC adapter from the power outlet.
CONTROLLING THE UNIT USING
A TRIGGER INPUT SIGNAL
When 12 V DC is input to the +12 V TRIGGER IN
jack, the anamorphic lens moves to the operating
position (Refer to Figure 2) and trigger signal input
indicator on the top panel lights blue.
When 12 V DC is not input to the +12 V TRIGGER
IN jack, the anamorphic lens moves to the opposite
end from the operating position (Refer to Figure 1)
and trigger signal input indicator goes out.
Figure 1 Figure 2
Note:
Do not move the LN-11S1A lens slider by hand. If
the lens slider was moved by hands, it might cause
failure.
USING VP-11 OR VP-15 SERIES
TRIG. 2 OUTPUT JACK
USING VP-11 OR VP-15 SERIES TRIG. 2 OUTPUT JACK
LN-11S1A +12 V TRIGGER IN jack
Trigger cable
Connect the TRIG. 2 output jack of VP-11 series or
VP-15 series to the +12V TRIGGER IN jack of the
lens slider.
Display the projector’s setup menu and set Trigger 2
V-stretch to On and turn all other settings Off. (Refer
to Figure 3)
Standard 1
Auto Power Off
Trigger 2 Full
Trigger 2 Normal
Trigger 2 Zoom
Disable
Off
Off
Off
Trigger 2 V-stretch On
Trigger 2 Through Off
Reset Lamp Life
Reset All
Remote Control
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.
HDMI
Figure 3
When V-stretch is set for the projector’s aspect
mode, 12 V DC is automatically output from the
TRIG. 2 output jack and the anamorphic lens moves
to the operating position. (Under the settings given
above, 12 V DC is not output from the TRIG. 2
output jack in other aspect modes.)
For example, set the projector as described above.
If a movie having 2.35:1 cinemascope size is input
from HDMI1 and viewed under “full” aspect mode,
a black band will appear at the top and bottom of the
screen. Now, change the aspect mode to V-stretch.
The black bands at the top and bottom of the screen
will disappear, and the movie will be displayed at a
16:9 aspect ratio that fills the screen. At the same
time, 12 V DC is output from TRIG. 2 output jack, the
anamorphic lens moves in front of the projector’s
lens (operating position), and you can view the
movie at the correct aspect ratio of 2.35:1.